valutazioni - 3, GPA: 4.7
(
)
)
|
Facilità d'uso
The GMI 10 will communicate with NMEA 2000- or NMEA 0183-compatible sensors and devices, and can show information such as speed, heading, water depth, and fuel information when connected to the appropriate sensors. Product Registration Help us better support you by completing our online registration today. Go to Keep the original sales receipt, or a photocopy, in a safe place. For future reference, write down the serial number assigned to your GMI 10 in the space provided below. The serial number is located on a sticker on the back of the GMI 10. Serial number Contact Garmin Contact Garmin Product Support if you have any questions while installing or using your GMI 10. In the USA, go to or contact Garmin USA by phone at (913) 397.8200 or (800) 800.1020. In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000. In Europe, go to and click Contact Support for in-country support information, or contact Garmin (Europe) Ltd. by phone at +44 (0) 870.8501241. Packing List andAccessories Before installing your GMI 10, confirm that your package includes the following items. If any parts are missing, contact your Garmin dealer immediately. Standard Package • GMI 10 unit • Protective cover • Flush mount hardware • NMEA 0183 data wiring harness • 2 NMEA 2000 T-connectors • 2 NMEA 2000 terminators (1 male, 1 female) • 1 NMEA 2000 drop cable (2 m) • 1 NMEA 2000 power cable (2 m), (3 A fuse) • Installation instructions To install and use your GMI 10 1. Select a location (page 2). 2. Flush mount the GMI 10 (page 2. OptionalAccessories • Additional NMEA 2000 network components Tools Needed • Jigsaw or 3 17/32 in. (90 mm) hole saw, • Drill and drill bits • Center punch and hammer • Scissors • File and sandpaper • Phillips screwdriver • Anti-seize lubricant (optional) 3. Connect the GMI 10 to the sensors and to power (page 3). January 2010 190-01168-02 Rev. A Printed in Taiwan Step 1: Select a Location for the GMI 10 Consider the following when you select an installation location: • Provides optimal viewing as you operate your vessel. • Allows easy access to the keypad on the GMI 10. • Is strong enough to support the weight of the GMI 10 and protect it from excessive vibration or shock. • Allows room for the routing and connection of the cables. There should be at least a 3 inch (8 cm) clearance behind the case. • Is at least 9 1/2 in. (241 mm) from a magnetic compass, to avoid interference. • Mount the GMI 10 in an area that is not exposed to extreme temperature conditions. NOTE: The temperature range for the GMI 10 is from 5°F to 158°F (from -15°C to 70°C). Extended exposure to temperatures outside this range (in storage or operating conditions) may cause failure of the LCD screen or other components. This type of failure and related consequences are not covered by the manufacturer’s limited warranty. Step 2: Flush Mounting the GMI 10 In addition to four of the included mounting screws (number 8 ANSI (4.2 . 1.4 DIN7981)), flush mounting the GMI 10 requires the following tools: • Phillips screwdriver • Drill and 1/8 in. (3.2 mm) drill bit for mounting holes • 3 17/32 in. (90 mm) hole saw for pilot hole • Scissors • Center punch and hammer • File and sandpaper • Anti-seize lubricant (optional) • Counterbore bit (for fiberglass installations) NOTE: Ensure that the surface on which you mount the GMI 10 has sufficient open space behind it to accommodate the GMI 10 and the connected wires. To flush mount the GMI 10: 1. The flush-mount template is included in the product box. Trim the template and ensure that it will fit in the location at which you want to flush mount the GMI 10. 2. The flush-mount template has adhesive on the back. Remove the protective liner and apply the template to the location where you want to flush mount the GMI 10. 3. Using the 3 17/32 in. (90 mm) hole saw, cut the mounting surface along the inside of the dashed line indicated on the flush-mount template. Use a file and sandpaper to refine the size of the hole. 4. Place the GMI 10 into the cutout to confirm that the four mounting-holes are correct after refining the hole. If not, mark the correct locations of the four mounting holes. Remove the GMI 10 from the cutout. 5. Using the center punch, indent the center of each of the four mounting-hole locations. 6. Using a 1/8 in. (3.2 mm) drill bit, drill the four mounting holes. NOTE: If you are mounting the chartplotter in fiberglass, it is recommended to use a countersink bit to drill a clearance-counterbore through only the top gel-coat layer. This will help to avoid any cracking in the gel-coat layer when the screws are tightened. GMI 10 Installation Instructions 7. Place the GMI 10 into the cutout. 8. Securely tighten the four mounting screws through the GMI 10 into the drilled mounting holes. NOTE: Stainless-steel screws may bind when screwed into fiberglass and overtightened. Garmin recommends applying an anti-galling, stainles...