Such a connection could cause a fire hazard and/or electric shock. DO NOT expose the transceiver to rain, snow or any liquids. DO NOT reverse the polarities of the power supply when connecting the transceiver. DO NOT apply an RF signal of more than 20 dBm (100mW) to the antenna connector. This could damage the transceiver's front end. ORDERING PARTS Be sure to include the following four points when ordering replacement parts: 1. 10-digit order numbers 2. Component part number and name 3. Equipment model name and unit name 4. Quantity required 1130007610 S.IC ^PD3140GS IC-F3GT 8810009510 Screw BT M2 x 4 NI-ZU IC-F3GS IC-F3GT IC-F3GS MAIN UNIT 1 pieces Chassis 10 pieces Addresses are provided on the inside back cover for your convenience. REPAIR NOTES 1. Make sure a problem is internal before disassembling the transceiver. 2. DO NOT open the transceiver until the transceiver is disconnected from its power source. 3. DO NOT force any of the variable components. Turn them slowly and smoothly. 4. DO NOT short any circuits or electronic parts. An insulated turning tool MUST be used for all adjustments. 5. DO NOT keep power ON for a long time when the transceiver is defective. 6. DO NOT transmit power into a signal generator or a sweep generator. 7. ALWAYS connect a 40 dB to 50 dB attenuator between the transceiver and a deviation meter or spectrum analyzer when using such test equipment. 8. READ the instructions of test equipment thoroughly before connecting equipment to the transceiver. TABLE OF CONTENTS SECTION 1 SPECIFICATIONS SECTION 2 INSIDE VIEWS SECTION 3 DISASSEMBLY AND OPTION INSTRUCTIONS 3-1 DISASSEMBLY INSTRUCTION ..............................................3-1 3-2 OPTIONAL UNIT INSTALLATIONS............................................3-2 SECTION 4 CIRCUIT DESCRIPTION 4-1 RECEIVER CIRCUITS.....................................................4-1 4-2 TRANSMITTER CIRCUITS .................................................4-1 4-3 PLL CIRCUITS ...........................................................4-2 4-4 POWER SUPPLY CIRCUITS................................................4-3 4-5 CPU PORT CIRCUITS.....................................................4-4 SECTION 5 ADJUSTMENT PROCEDURES 5-1 PREPARATION ..........................................................5-1 5-2 PLLADJUSTMENT .......................................................5-3 5-3 TRIMMER ADJUSTMENT ..................................................5-4 5-4 TRANSMITTER ADJUSTMENT ..............................................5-6 5-5 RECEIVER ADJUSTMENT..................................................5-6 SECTION 6 PARTS LIST SECTION 7 MECHANICAL PARTS AND DISASSEMBLY SECTION 8 SEMI-CONDUCTOR INFORMATION SECTION 9 BOARD LAYOUTS 9-1 GENERAL AND EIA/TIA VERSIONS (EXCEPT W/N-TYPE).........................9-1 9-2 ETS/CEPT VERSION......................................................9-3 9-3 W/N-TYPE ..............................................................9-5 SECTION 10 BC-137 OPTIONAL DESKTOP CHARGER INFORMATION 10-1 PARTS LIST.............................................................10-1 10-2 DISASSEMBLY INFORMATION..............................................10-1 10-3 VOLTAGE DIAGRAM......................................................10-2 10-4 BOARD LAYOUT.........................................................10-2 SECTION 11 BLOCK DIAGRAM SECTION 12 VOLTAGE DIAGRAM SECTION 1 SPECIFICATIONS ETS 300 086 EIA/TIA 603 GENERAL Frequency coverage 136.000-150.000 MHz (L-band), 146.000-174.000 MHz (H-band) Type of emission 16K0F3E (W-type), 14K0F3E (M-type), 8K50F3E (N-type) Number of channels 100 ch (100 channel version), 32 ch (16 channels x 2 banks: 2-BANK version), 16 ch (16 channel version) Power supply requirement 7.2 V DC (negative ground; supplied battery pack) Current drain (approx.) TX at High 1.6 A at Low 700 mA RX rated audio 250 mA stand-by 70 mA Frequency stability ±2000 Hz (W/M-type), ±1.5 kHz (N-type) ±0.0005% Usable temperature range -25°C to +55°C -30°C to +60°C Dimensions (proj. not included) 54(W) x 132(H) x 35(D) mm; 2V8(W) x 5732(H) x 138(D) inch Weight (with BP-209) 370 g; 13.1 oz TRANSMITTER Output power High 5 W Low 1 W Modulation system Variable reactance frequency modulation Max. freqequency deviation ±5.0 kHz (W-type), ±4.0 kHz (M-type)*1, ±2.5 kHz (N-type) Spurious emissions 0.25 |JW @ < 1 GHz, 1.00 jW @ > 1 GHz 73 dBc typical Adjacent channel power 70 dB (W/M-type) 60 dB (N-type) 70 dB typical (W-type) 60 dB typical (N-type) Transmitter audio distortion Less than 5% at 1 kHz, 60% deviation Less than 3% at 1 kHz, 40% deviation Limitting charact of modulator 70-100% of max. deviation Ext. microphone connector 3-conductor 2.5(d) mm (1/10")/2.2 kQ RECEIVER Receive system Double-conversion superheterodyne system Intermediate frequencies 1st: 31.05 MHz,...