valutazioni - 3, GPA: 4.7
(
)
)
|
Facilità d'uso
Using an adapter that does not meet these specifications could damage the cassette recorder or the adapter. • Always connect the DC adapter to the cassette recorder before you connect it to the power source. When you finish, disconnect the adapter from the power source before you disconnect it from the cassette recorder. 1. Set the adapter’s voltage switch to 9V, if necessary, then connect the Adaptaplug to the DC adapter’s cord so the tip reads TIP–. 2. Insert the barrel plug into the recorder’s DC 9V jack. 3. Plug the other end of the adapter into the 12V power source. Notes: • If the cassette recorder does not operate properly when you use DC power, be sure the 12V source (such as a cigarette- lighter socket) is clean and that the adapter’s plug is pushed all the way into the socket. • Disconnect the adapter when you are not using the cassette recorder. • Internal batteries (if installed) automatically disconnect when you plug the adapter into the DC 9V jack. LISTENING SAFELY To protect your hearing, follow these guidelines when you use headphones. • Set the volume to the lowest setting before you begin listening. After you begin listening, adjust the volume to a comfortable level. • Do not listen at extremely high volume levels. Extended high-volume listening can lead to permanent hearing loss. • Once you set the volume, do not increase it. Over time, your ears adapt to the volume level, so a volume level that does not cause discomfort might still damage your hearing. TRAFFIC SAFETY Do not wear headphones while operating a motor vehicle or riding a bicycle. This can create a traffic hazard and could be illegal in some areas. Even though some headphones let you hear some outside sounds when listening at normal volume levels, they still can present a traffic hazard. 2 PHONES — connect a pair of TONE HIGH/LOW — slide TONE BAND AM/FM/FM STEREO — slide to se- headphones (not supplied) with to high to enhance the treble lect the band. Select FM STEREO to hear a 1/8-inch (3.5-mm) plug. Your lo-sound or to LOW to enhance the sound in stereo. If the reception using FM cal RadioShack store carries a wide selection of headphones. Insert the headphones’ 1/8-inch (3.5-mm) plug into the cassette recorder’s PHONES jack. Note: Connecting headphones automatically disconnects the built-in speaker. bass sound. FUNCTION RADIO OFF/TAPE/RADIO — slide to turn the radio on and off and to use the cassette functions. STEREO is weak, select FM instead. The sound will be monaural, but the reception should improve. TUNING — rotate to select the desired AM or FM station. VOLUME — rotate to adjust the sound volume. The radio/cassette player’s automatic level control circuitry automatically adjusts the recording level. Adjusting VOLUME does not affect the recording. Antenna — to get the best FM re- ception, fully extend the telescoping antenna. The AM antenna is built-in. For the best AM reception, rotate the radio. PAUSE — press to temporarily stop a tape. Press again to resume play, recording, rewind- ing, or fast-forwarding. STOP/EJECT — press to stop tape play, recording, fast-forwarding, or rewinding, or to open the cassette com- partment door. Note: The radio/cassette player’s auto stop function saves battery life by turning off the motor and releasing the tape-handling parts when the tape reaches its end. REWIND — press to rewind a tape to the desired location. PLAY RECORD — press to record from the radio or live, using the built-in MIC. Note: Sometimes taped AM broadcasts produce a whis- tling sound that you can hear, called a “beat.” Slide BEAT CUT (on the back of the radio/cassette player) to the position that produces the best quality recording. FAST-F — press to fast-forward a tape to the desired location. USING THE RADIO 1. Set FUNCTION to RADIO to turn on the radio. 2. Set BAND to the desired setting (AM, FM, or FM STEREO). 3. Adjust VOLUME as desired. 4. Rotate TUNING to select a radio station. 5. When finished, set FUNCTION to TAPE to turn off the radio. LOADING A CASSETTE TAPE 1. Take up any slack in the tape by turning the cassette’s hub with a pencil or your finger. If you do not remove excess slack, the tape might become tangled in the record/playback mechanism. Avoid touching the tape. 2. Press STOP/EJECT to open the cassette compartment door. 3 3. Load the cassette with its open edge facing up, its full reel to the right, and the side you want to play facing out. 4. Gently close the compartment door. PLAYING A CASSETTE TAPE 1. Set FUNCTION to TAPE. 2. Load a cassette tape. 3. Press PLAY. 4. Adjust VOLUME as desired. 5. Press STOP/EJECT to stop playback before it automatically stops at the end of the tape. Press STOP/EJECT again to open the cassette compartment so you can remove the cassette tape. RECORDING You can record from the radio, or use the built-in microphone to make a live recording. Caution: Before you load a cassette tape for recording, be sure its erase-protection tabs are in place. If you force down ...
Questo manuale è adatto anche per i modelli :Ricevitori - SCR-64 (98.54 kb)