valutazioni - 4, GPA: 4.3
(
)
)
|
Facilità d'uso
All Rights Reserved. RadioShack, RadioShack.com, and Adaptaplug are trademarks used by RadioShack Corporation. cassette recorder stops operating properly, replace the batteries. Warning: Dispose of old batteries promptly and properly. Do not burn or bury them. Caution: If you do not plan to use the cassette recorder with batteries for a week or longer, remove the batteries. Batteries can leak chemicals that can destroy electronic parts. USING AC OR DC POWER You can power the cassette recorder with standard AC power using a 6V, 700 mA AC or DC adapter and a size M Adaptaplug™ connector (neither supplied) available at your local RadioShack store. Cautions: ! You must use a Class 2 power source that supplies 6V DC and delivers at least 700 mA. Its center tip must be set to negative and its plug must fit the cassette recorder’s DC 6V jack. Using an adapter that does not meet these specifications could damage the cassette recorder or the adapter. • Always connect the AC or DC adapter to the cassette recorder before you connect it to a power source. When you finish, disconnect the adapter from its power source before you disconnect it from the cassette recorder. 1. Set the adapter’s voltage switch to 6V, if necessary, then connect the Adaptaplug to the adapter’s cord so the tip reads TIP–. 2. Insert the barrel plug into the recorder’s DC 6V jack. 3. Depending on which power source you are using, plug the other end of the adapter into a standard AC outlet or a vehicle’s 12V power source, such as a cigarette-lighter socket. Notes: • Connecting an AC or DC adapter automatically disconnects internal batteries, if installed. • If the cassette recorder does not operate properly when you use DC power, be sure the 12V source (such as a cigarette- lighter socket) is clean and that the adapter’s plug is pushed all the way into the socket. • Disconnect the adapter when you are not using the cassette recorder. • Internal batteries (if installed) automatically disconnect when you plug the adapter into the DC 6V jack. LISTENING SAFELY To protect your hearing, follow these guidelines when you use headphones. • Set the volume to the lowest setting before you begin listening. After you begin listening, adjust the volume to a comfortable level. • Do not listen at extremely high volume levels. Extended high-volume listening can lead to permanent hearing loss. • Once you set the volume, do not increase it. Over time, your ears adapt to the volume level, so a volume level that does not cause discomfort might still damage your hearing. TRAFFIC SAFETY Do not wear headphones while operating a motor vehicle or riding a bicycle. This can create a traffic hazard and could be illegal in some areas. Even though some headphones let you hear some outside sounds when listening at normal volume levels, they still can present a traffic hazard. 2 VOLUME — slide to adjust the sound volume. The radio/cassette player’s automatic level control circuitry automatically adjusts the recording level. Adjusting VOLUME does not affect the recording. Phones — connect a pair of headphones (not supplied) with a 1/8-inch (3.5-mm) plug. Your local RadioShack store carries a wide selection of headphones. Insert the headphones’ 1/8-inch (3.5-mm) plug into the cassette recorder’s phones jack. Note: Connecting headphones automatically disconnects the built-in speaker. PAUSE — press to temporarily stop a tape. Press again to resume play, recording, rewinding, or fast-forwarding. STOP/EJECT — press to stop tape play, recording, fast-forwarding, or rewinding, or to open the cassette compartment door. Note: The radio/cassette player’s auto stop function saves battery life by turning off the motor and releasing the tape-handling parts when the tape reaches its end. USING THE RADIO TONE LOW/HIGH — slide TONE to LOW to enhance the bass sound or to HIGH to enhance the treble sound. TAPE RADIO OFF/RADIO — slide to turn the radio on and off and to use the cassette functions. PLAY FAST-F — press to fast- forward a tape to the desired location. REWIND — press to rewind a tape to the desired location. 1. Slide TAPE RADIO OFF/RADIO to RADIO. 2. Slide AM/FM/FM STEREO to the desired band. 3. Adjust TUNING to the desired station. 4. Adjust VOLUME MIN/MAX as desired. 5. Slide TAPE RADIO OFF/RADIO to TAPE RADIO OFF to turn off the radio. LOADING A CASSETTE TAPE 1. Take up any slack in the tape by turning the cassette’s hub with a pencil or your AM/FM/FM STEREO — slide to select the band. Select FM STEREO to hear sound in stereo. FM STEREO lights when receiving an FM station in stereo. If the reception is weak when using FM STEREO, select FM instead. The sound will be monaural, but the reception should improve. Antenna — to get the best FM reception, fully extend the telescoping antenna. The AM antenna is built-in. Rotate the radio for the best AM reception. TUNING — rotate to select the desired AM or FM station. RECORD — press to record from the radio or live, using the built-in MIC. N...
Questo manuale è adatto anche per i modelli :Ricevitori - SCR-65 (84.43 kb)