valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
PLAYING A CASSETTE TAPE 1. Set STANDBY REC to OFF. 2. Set TAPE SELECT to either NORMAL or CrO2 according to the type of tape you are going to play. 3. Press PLAY . The PLAY indicator lights. 4. Adjust VOLUME to a comfortable listening level. 5. To stop the tape, press STOP/ EJECT . Press STOP/EJECT again to open the cassette compartment’s door and remove the cassette tape. Notes: • To temporarily stop playback, press PAUSE . To resume playback, press PAUSE again. • At the end of a tape, the tape motor automatically stops and the selected button (PLAY , RECORD , CUE/FAST-F , or REVIEW/REWIND ) pops up. • To play the other side, turn the cassette tape over. Fast-Forward and Rewind Press CUE/FAST-F to rapidly advance a tape. Press REVIEW/REWIND to quickly rewind a tape. When the tape reaches the desired point, press STOP/EJECT . Caution: To avoid damaging the tape, do not go directly from rewind to fast- forward or from fast-forward to rewind without pressing STOP/EJECT first. Cue and Review Holding down CUE/FAST-F while playing a cassette tape lets you cue (play the cassette tape at high speed) so you can quickly locate any desired section on the tape. When you release CUE/FAST-F , the recorder returns to normal play. Holding down REVIEW/REWIND after you press PLAY lets you review (play the cassette tape in reverse at high speed). When you release REVIEW/REWIND , the recorder returns to normal play. RECORDING Recording from the Radio 1. Set STANDBY REC to OFF. 2. Load the cassette tape you want to record on. 3. Set TAPE SELECT to either CrO2 or NORMAL according to the tape you loaded. 4. Tune to the desired station. 5. Adjust VOLUME to a comfortable listening level. Note: The Automatic Level Control automatically adjusts the volume recorded on the tape. 6. Press RECORD to begin recording. PLAY automatically goes down and the RECORD indicator lights. The DX-392 automatically stops when the tape reaches the end. To record the other side, turn the tape over. Caution: Never attempt to force down RECORD . If you have removed your cassette’s erase- protection tabs, you cannot press RECORD . See “Accidental Erasure Prevention” on Page 32. 7. To temporarily stop recording, press PAUSE . Press PAUSE again to resume recording. 8. When the recording is complete, press STOP/EJECT twice, and remove the cassette from the recorder. Recording from the Radio Using the Standby Feature This feature lets you record your favorite program at a preset time. 1. Turn on the receiver and tune to the desired station. 2. Turn off the receiver. 3. Set STANDBY REC to ON. 4. Set STANDBY BUZZER/RADIO to RADIO. 5. Press STANDBY. 6. While STANDBY flashes, enter the starting time of the program you want to record. Then press ENTER. STANDBY stops flashing. Note: Be sure the clock display is set to show the desired clock when the alarm time arrives. 7. Load a tape with adequate length for the period you are going to record. For instance, load a C-60 tape for recording a 30-minute program. 8. Set TAPE SELECT to either CrO2 or NORMAL according to the type of tape you loaded. 9. Press RECORD (PLAY automatically goes down). The radio turns on at the preset time and the recorder starts recording. The tape stops automatically at the end of the tape, but the radio keeps playing until you turn it off. Recording AM Broadcasts Sometimes you might hear a hum or whistling sound when recording an AM broadcast. To reduce or eliminate this sound, set the BEAT CUT switch to the position that gives you the best recording. Recording Using the Built-In Microphone Your cassette recorder has a built-in condenser microphone on the front. To record with the built-in microphone, follow the steps in “Recording from the Radio” on Page 19. But, instead of tuning to a radio station in Step 4, simply position the DX-392 near the source you are recording. Then continue with Step 6. ADDITIONAL FEATURES CONNECTING HEADPHONES For private listening and for stereo sound during FM stereo broadcasts, you can connect optional stereo headphones with a 1/8-inch plug. Your local Radio Shack store sells a wide selection of stereo headphones. Insert the headphones’ plug into the receiver’s jack. This disconnects the receiver’s internal speaker. When you connect stereo headphones and tune to a stereo broadcast, appears on the display. For the best reception, fine tune the receiver until ST ST remains steady. Listening Safely To protect your hearing, follow these guidelines when you use headphones. • Set the volume to the lowest setting before you begin listening. After you begin listening, adjust the volume to a comfortable level. • Do not listen at extremely high volume levels. Extended high- volume listening can lead to permanent hearing loss. • Once you set the volume, do not increase it. Over time, your ears adapt to the volume level, so a volume level that does not cause discomfort might still damage your hearing. LIGHTING THE DISPLAY Press LIGHT to briefly light the display. The dis...
Questo manuale è adatto anche per i modelli :Ricevitori - DX-392 (307.99 kb)