valutazioni - 5, GPA: 4.4
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Stereo - CT-W208R (934.81 kb)
Stereo - CT-W208R (388.75 kb)
Stereo - CT-W208R (214.8 kb)
Stereo - CT-W208R (331.66 kb)
Facilità d'uso
Wrong connection, connection cord removed, poor contact, broken wire. . . . Turn REC LEVEL control up (see page 14). Set the amplifier recording output selector correctly. Check connections (see page 7). Immediately stops. . . The tape is completely wound. The tape is slack. . . . Record in the opposite direction. Rewind the tape. Take up the slack (see page 6). Cannot record. . The head is dirty. . Clean the head (see page 5). No sound. . Connection problems (wrong connection, cord removed, poor contact, broken wire.) . . Check that the recording and playback connection cords are connected correctly (see page 7). Set the amplifier selector correctly. REC LEVEL control does not function. . The tape is being copied. . When recording is finished, REC LEVEL control will function. TROUBLESHOOTING Symptom Cause Remedy POOR SOUND QUALITY Unstable or interrupted sound. . The head, pinch rollers and capstans are dirty. O The tape is not uniformly wound. . . Clean the head (see page 5). Completely fast-forward or rewind the tape. No high frequencies. O A tape recorded without Dolby NR is being played back with the DOLBY NR switch in the B or C position. . The head is dirty. O . Set the DOLBY NR switch to OFF. Clean the head (see page 5). High frequencies are emphasized. . A Dolby NR-encoded tape is being played back with the DOLBY NR switch in the OFF position. O Set DOLBY NR (B/C) switch to the same position used for recording. Sound from previous recordings remains when rerecording a tape. . The head is dirty. . Clean the head (see page 5). The sound is disO Recording level is too high. O Turn REC LEVEL control down when torted. O The recorded signal itself is distorted. . The head is dirty. O . recording(see page 14). Replace the cassette. Clean the head (see page 5). Too much noise. O High noise tape is being used. O Incomplete insertion of a connection cord, poor contact. O Recording level is too low. . The head is dirty. O The head is magnetized. OOO . O Replace the cassette. Check connections (see page 7). Turn REC LEVEL control up when recording (see page 14). Clean the head (see page 5). Demagnetize with a head demagnetizer (see page 5). OTHERS The music search function does not work. . Blanks between selections are less than 4 seconds long. O Use a tape with blanks more than 4 seconds long. Cannot use the remote control system. O The remote control cord is not connected. O Connect the remote control cord (see page 7). Abnormal functioning of this unit may be caused by static electricity, or other external interference. To restore normal operation, turn the power off and then on again, or unplug the AC power cord and then plug it in again. 18 19 SPECIFICATIONS System ................... 4-track, 2-channel stereoHeads ”Hard Permalloy” recording/playback head x 1 “Hard Permalloy” playback head x 1 “Ferrite” erasing head x 1 Motor......................................... DC servo motor x 2 Wow and Flutter ............................... 0.09% (WRMS) ±0.19% (DIN) Fast Winding Time Approximately 100 seconds (C-60 tape) Frequency Response –20 dB recording: TYPE IV (Metal) tape...................... 20 to 16,500 Hz TYPE II (High/CrO) tape ................ 20 to 16,000 Hz 2 TYPE I (Normal) tape ..................... 20 to 16,000 Hz Signal-to-Noise Ratio Dolby NR OFF...............................More than 57 dB Noise Reduction Effect Dolby B-type NR ON... More than 10 dB (at 5 kHz) Dolby C-type NR ON... More than 19 dB (at 5 kHz) Harmonic Distortion.................. No more than 0.8% (at –4 dB: 160 nwb/m) Input (Sensitivity) LINE (INPUT) ..... 100 mV (Input impedance 68 kW) Output (Reference level) LINE (OUTPUT) ... 0.5 V (Output impedance 1.9 kW) Subfunctions OAutomatic reverse ODOLBY B/C type NR OMusic search over ±15 selections OSynchronized copy start OHigh-speed and normal-speed copy (DECK I =DECK II) ORelay playback/blank skip OPeak level meter with peak-hold function OAutomatic space recording mute OAutomatic tape selector OeSystem remote control available Miscellaneous Power Requirements U.K. and Australian models .................................... AC 230 ~ 240 volts, 50/60 Hz U.S. model ..................................... AC 120 V, 60 Hz Power Consumption ......................................... 16 W Dimensions ............ 420 (W) x 125 (H) x 250 (D) mm (16 - 9/16 (W) x 4 - 7/8 (H) x 9 - 13/16 (D)in.) Weight (without package) U.K. and Australian models ....... 3.9 kg(8 lb 10 oz) U.S. model ..................................... 3.8 kg(8 lb 6 oz) Accessories Operating instructions ............................................. 1 Connection cord with pin plugs .............................. 2 Control cable ........................................................... 1 Warranty card ........................................................... 1 NOTE: Specifications and design subject to possible modifications without notice, due to improvements. Published by Pioneer Electronic Corporation. Copyright © 1999...