valutazioni - 3, GPA: 3.3
(
)
)
|
Facilità d'uso
2) Route power, speaker, and antenna cables through hole, and connect to unit as shown in hook up diagram below. 3) After making sure connections are correct, test unit operation as described in the operation section (Do not mount until AM antenna trimmer adjustment has been made. WIRING COLOR CODE FOR AWM-820 NOTES: - Speakers must have a minimum of four W impedance each. -Either antenna may be used. Both do not have to be hooked up at the same time. - Do not operate this unit with only one speaker hooked up. If a speaker fails, replace it before operating this unit. COLOR ORANGE/WHITE GREEN/WHITE BLACK/WHITE WHITE VIOLET BLUE LIGHT GREEN RED VIOLET/BLACK YELLOW LT.GREEN/BLACK FUNCTION +12VDC IGNITION POWER +12VDC BATTERY POWER TO CHASSIS GROUND LEFT (A) SPEAKER (+) LEFT (A) SPEAKER (-) RIGHT (A) SPEAKER (+) RIGHT (A) SPEAKER (-) LEFT (B) SPEAKER (+) LEFT (B) SPEAKER (-) RIGHT (B) SPEAKER (+) RIGHT (B) SPEAKER (-) NOTE: Always be sure when running cables to avoid sharp edges, extreme heat sources, and any other potential hazards. 2 OPERATING INSTRUCTIONS NOTE: Number in parenthesis (#) corresponds with “Identification of Controls / Connections” on page 1 of this manual. LIQUID CRYSTAL DISPLAY PANEL The liquid crystal display (LCD) panel displays the frequency, time, and activated functions. Note: It is a characteristic of LCD panels that if subjected to cold temperatures for an extended period of time, they will take longer to illuminate than under normal conditions. In addition, the visibility on the numbers of the LCD may slightly decrease. The LCD read out will return to normal when the temperature increases to a normal range. TUNER 1) Turn power on by pushing the Power Switch Control Button (17). 2) Use the Source Selectors (18), select the AM /FM button. 3) Use the Speaker Selector Switch (13) to choose between speaker output, headphones, or both. 4) Use Tuning Up (1) or Down (2) buttons to select the station manually. Also, the Station Preset buttons can select stations (this will be discussed later in the manual). Push either of the Seek buttons (1 or 2) to tune to the next higher or lower active station. 5) Adjust Volume Control (17) to suit taste. CASSETTE TAPE PLAYER 1) Turn power on by pushing the Power Switch/Volume Control button (17). 2) Use the Source Selectors (18), to select the TAPE button. 3) Use the Speaker Selector Switch (13) to choose between speaker output, headphones, or both. 4) Press the Cassette Eject button (12) to eject any cassettes that may already be in the player. 5) Insert a cassette into the Cassette Player (11). 6) The cassette will automatically play when inserted. 7) You may rewind or fast forward the cassette using the REW or F.F. buttons (10 and 9). 8) To change sides of the cassette, press the REW and F.F. buttons (10 and 9), simultaneously. 9) To eject the cassette, press the Cassette Eject button (12). 3 AUXILIARY INPUT 1) Push Power Switch (17) “on”. 2) Using the Source Selectors (18), choose the button labeled “AUX”. 3) If there is an external source (ie. CD shuttle) connected to the Auxiliary In Jacks (21) on the rear of the radio, then you can listen to your external source through the system. 4) An external auxiliary source can also be used (such as a portable cassette player) through the 1/8” Auxiliary Stereo Input Jack (14) on the front of the radio. SETTING THE CLOCK 1) Push the Power Switch (17) “on”. 2) Hold the T/ F button (4). 3) Use the H and M buttons (1 and 2) to adjust hours and minutes. Note: The T/ F also toggles between time and radio frequency on the display. SETTING STATIONS INTO MEMORY PRESET 1) This unit has the ability to set 18 FM and 12 AM stations into memory. 2) To set the AM or FM stations into memory, first tune to the desired station. 3) Once at the desired station, press and hold preset button (8) you wish to program for more than 3 seconds. USING THE AUDIO ADJUST BUTTON 1) You can toggle between volume, treble, bass, and balance control by pressing the Audio Adjust button (16). 2) Once at the desired function, you can use the volume knob to adjust. SETTING THE ALARM 1) Hold the Alarm Set button (6). 2) Use the H and M buttons (1 and 2) to adjust hours and minutes. 3) The Alarm On /Off button (6) activates or deactivates the alarm. 4 BEEP FEATURE 1) Hold the Audio Adjust button to enable the beep feature (16). Lower right side will display an audio symbol when this feature is turned on. 2) When this feature is on, turning different features on or off will produce two different tones, higher tone for ON, and lower tone for OFF. 3) Completely removing power from the unit will turn the beep feature off. AS/PS BUTTON This button is for Auto-Store Tuning (AS) and Pre-set Scan Tuning (PS) (3) 1) Press this button momentarily during radio operation to scan the stations pre-set into the memories of that band. The unit will stop at each pre-set station for approx. 5 seconds before continuing on to the next pre-set station Press this button ...