valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
In accordance with FCC requirements, changes or modifications not expressly approved by Thomson Consumer Electronics could void the user’s authority to operate this product. HEADPHONES USE When you attach headphones (not included), the speaker is automatically silenced for private listening. Make sure you turn down the volume on the unit before you put on headphones. Increase the volume to the desired level only afterheadphones are in place. POWER There are two ways to supply power to your recorder: BATTERY INSTALLATION 1. Press down on the battery door and slide in the direction of the arrow. 2. Insert two "AA" batteries - not included- as shown in the diagram on the back of the unit. 3. Replace the battery door. IMPORTANT BATTERY INFORMATION • Alkaline batteries are recommended for best results. Using nickel-cadmium rechargeable batteries may result in shorter playing time. • If you do not intend to use the unit for a month or more, remove the batteries to avoid leakage or subsequent damage. • Dispose of batteries in the proper manner, according to federal, state and local regulations. • Any battery may leak electrolyte if mixed with a different battery type; if inserted incorrectly; if all batteries are not replaced at the same time; if disposed of in fire; or if an attempt is made to charge a battery not intended to be recharged. • Discard leaky batteries immediately to avoid possible skin burns or other personal injury. AC/DC POWER CONVERTER (NOT INCLUDED) You can use an AC/DC power converter to operate your recorder. Plug the barrel end of the converter into the recorder's 3V DC jack - automatically disconnecting the batteries - and then plug into an AC household outlet. ©1997 Thomson Consumer Electronics, Inc. Trademark(s) ® Registered Marca(s) ® Registradas Model 3-5362 20800020 (Rev. 0, E/S) 97-08 Printed in China TO INSERT OR REMOVE A CASSETTE Make sure all buttons are in their "off" (up) position before attempting to open the cassette compartment door. 1. Grasp both sides of the cassette compartment door and lift up. 2. Gently slide in a cassette with the exposed tape facing out and the side you want to hear/record on showing through the cassette door window. 3. Close cassette compartment door. MIC SENSITIVITY SWITCH Select HI sensitivity for recording at conferences or for general use. Select LO sensitivity for close dictation. RECORDING 1. Insert a blank cassette. 2. Select MIC sensitivity (HIGH or LOW). 3. Press the RECORD button. (The PLAY button will automatically depress at the same time). NOTE: If the RECORD button does not depress, see "Preventing Accidental Erasure." 4. Speak normally into the microphone. To obtain optimum recording quality, place the recorder with the microphone freely exposed to sound source and as close as conveniently possible. 5. When you finish recording, press the STOP button. NOTES: The ALC (Automatic Level Control) will set the record level for optimum recordings, regardless of volume setting. Avoid recording near unwanted noise sources, such as air conditioners, fans, etc. PAUSE The PAUSE feature allows you to momentarily stop tape activity in any mode without resetting the control buttons. To use, simply slide the PAUSE switch to the ON position to stop activity. Slide the switch back to the OFF position to resume activity. PLAYBACK To listen to a prerecorded cassette: 1. Insert a cassette as explained above. 2. Press the REW button to rewind the tape to its starting point if necessary. 3. Press the PLAY button. 4. Adjust VOLUME to desired level. VARIABLE SPEED PLAYBACK During the Play mode, you can adjust the speed of prerecorded tapes by rotating the Variable Speed Playback knob towards the MAX (maximum) position. Tape playback will be approximately 30-50 percent faster than normal at the full MAX position. F.FWD AND REW When not in the Play mode, you can use these buttons to adjust the tape position. Press F.FWD to move the quickly forward. Press REW to move the tape quickly backward. CUE/REVIEW This feature is helpful in finding the beginning or the end of the recorded segment on the tape. When in the Play mode, press and hold the F.FWD or REW button and listen for a change from noise to silence (signaling the end of the recording) or from silence to noise (beginning of recording). When you reach the portion of tape you want to hear, release the F.FWD or REW button. Use the same procedure if you want to skip a prerecorded portion or if you want to hear the same portion again. AUTOMATIC STOP When the unit is operating in the Play or Record mode and the tape reaches its end, the unit will automatically shut itself off and return all buttons to their off position. ERASING CASSETTES To erase a tape or a portion of a tape, simply rewind and record over the unwanted material. PREVENTING ACCIDENTAL ERASURE Whenever you make a recording, any previous material on the tape is automatically erased. When you have a recording you want to keep permanently, break out the...