valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
Already-inserted cassette remains in unit. Current settings and source mode are stored. If power was not switched off before face removed, unit will automatically power- on when face is reattached. Power (PWR) On/Off When ignition on, press PWR or insert a disc to turn unit on. Last-used source becomes active, unless unit is turned on by inserting tape, in which case tape player becomes active. Power Off Press PWR to turn unit off. Unit stores current settings for source, station or track, etc. Antenna/ amplifier trigger wire shuts off voltage. (If faceplate still attached, display switches to clock.) Setting the Clock Turn the unit on. Press the CLK Button for four seconds until the clock starts blinking. (The display will change after two seconds. Ignore this and continue to hold for two more seconds.) Once the clock starts blinking, Press the A to set the hour, and press the V Button to set the minutes. (To change the minute indicator to the nearest hour (:OO), you can press the MUTE Button. Press the CLK Button again to activate the clock. 3 Changing the Information Displayed The display priority choices are clock or functional information (radio freqency, “TAPE 1 or 2”, and Track Number/Disc Number for changer. l To change the display priority, press the CLK Button for two seconds. The display priority changes. The display priority choices are clock or radio frequency/“TAPE”/Track No. and Disc No. l To change the display temporarily, press and release the CLK Button to access the desired information. After four seconds, the display changes back to the priority information. Source (SRC) Use SRC to select source - AMT, FMl, FM2, FMT Cassete (if already inserted), and/or CD Changer (if connected). Audio Operation Volume Control Buttons (+/-) Press +and - to increase/decrease volume from 0 to 63, in increments of 1.25 dB/step. Volume control is accessible from all modes except Bass, Treble, Balance and Fade modes. Adjustable Maximum Turn-On Volume First adjust the volume to the (maximum) volume level desired when the unit is turned on. Press and hold the PWR Button for more than two seconds. The unit turns off and the turn-on volume level is memorized. When the unit is turned on, the volume will be at the memorized level, even if the unit was turned off while the volume was at a higher level. However, if the volume is turned off when the volume level is lower than the stored Turn-On volume level, the volume will be at the lower level when the unit is turned back on. Mute Press Mute to temporarily reduce volume by 20 dB. “MUTE” appears. Mute is terminated by pressing any button. AUDIO TS AUDIO TS Bass, Treble, Balance and Fade Press Mute/AUDIO for more than l/2 second to access Bass. Subsequent presses access Treble, Balance and Fade modes. Bass -Adjust from +7 to -7 at 2 dB/step using + to increase bass, - to decrease. Treble - Adjust from +7 to -7 at 2 dB/step using + to increase treble,- to decrease. Balance - Adjust balance from 9 (all the way left) using + to -9 (all the way right) using -. Fader - Adjust fader from 9 (sound only from the front) using + to -9 (sound only from the rear) using -. Loudness (LD) Press LD to increase sound of low and high frequencies. LOUD icon appears. To cancel, press LD again. Radio Operation Last Station Memory Each FM bank and AM band has its own last station memory which holds last-tuned frequency for that band or bank irrespective of whether that frequency is stored into a preset. Selecting Bands Press SRC as needed to access FMl, FM2, FM3/FMT, AM/AMT banks. Seek Tuning Press A or V to seek next receivable frequency. Tuning stops at frequency that fulfills sensitivity requirements predetermined by sensitivity set through SENS/LD button. Tuning Sensitivity (SENS) Press SENS/LD for more that 2seconds to switch between local (lo) and distant search sensitivity. Radio Reception Hints l When listening to weak or distant AM stations, adjusting the Treble to minimum (-7) will reduce noise and improve sound. l In general, set SENS to in the distant mode ( so that “lo” does not appear) if in rural areas or where stations tend to be weak and distant, and to lo when in metropolitan areas or where stations tend to be strong and local. Stereo Symbol Stereo symbol turns on if a stereo station with an incoming signal of at least 20 dBpV is received. The unit gradually switches between mono to stereo automatically. Manual Tuning Press A or V for more than l/2 second and frequency will go one channel/step in direction pressed. Press and hold causes continuous manual tuning. Unit returns to seek tuning mode after 4 seconds or after storing a station on a preset. . Preset Station Storage After tuning desired frequency on desired band, press and hold a Preset Button for more than 2 seconds to store current frequency. Audio is muted during storage, preset number appears, and beep acknowledges storage. Preset Station Selection Press desired Preset Button. Travelstore This feature allows y...