valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
It provides both an easy way to carry the speaker system as well as a stand to support the speaker system when placed on a flat surface. Prop the speaker system on its adjustable handle The adjustable handle doubles as a stand. Rotate the handle to its rearmost position. Simply grasp and swing the handle backward from either the pack position or carry position. Lift the speaker system handle for carry Rotate the handle to its top position. Simply grasp and swing the handle backward from the pack position or forward from the kick-stand position. Pack up the speaker system Rotate the handle to its down point, tucking it snugly under the base of the speaker system. Simply grasp and swing the handle down from either the kick-stand position or carry position. When the handle is in the pack position, the speaker system will automatically turn off. WARNING In order to prevent accidentally dropping your iPhone or iPod, be sure to remove it from the docking station before picking up the speaker system by the handle. How to Install the AC Adapter 1 Connect the AC adapter cable plug into the speaker system’s jack. The jack is located on the back of the system. 2 Plug the AC adapter into the wall outlet. WARNING Use of another AC adapter may damage the product. Use only the supplied AC adapter. How to Charge the Lithium-Ion Battery Your Altec Lansing inMotion Kick speaker system includes a rechargeable lithium-ion battery. This battery should be fully charged before initial use of the speaker system. A full charge will provide up to 6.5 hours of continuous playing time. 1 Connect the speaker system to a wall outlet. See the How to Install the AC Adapter section. When the speaker system is on, the “Battery” LED will flash slowly to show the battery is charging. Once the battery is fully charged, the “Battery” LED will remain solid. 2 Allow the battery to charge. Charging time: Approximately 4 hours for a full charge. When the battery is low, the “Battery” LED will flash rapidly. WARNING During the recharging process, it is typical for the battery to become warm. To be safe, keep flammable materials away from the speaker system. How to Disconnect the Rechargeable Battery 1 Unplug the inMotion Kick from the wall outlet. 2 Remove the rechargeable battery compartment cover at the back of the system by removing the screw. 3 Unplug the battery and remove it. WARNING There is a danger of explosion if the battery is incorrectly replaced. Replace it only with the same or equivalent type. Do not expose it to excessive heat such as sunshine, fire, etc. BATTERY DISPOSAL The battery used in this product must be properly recycled or disposed of. Please contact your local recycling center for proper battery handling and disposal instructions. Rated Voltage: 3.7V Capacity: 1800mAh Type: McR18650 How to Install the Full-featured Remote Battery The full-featured remote battery (included) is not installed at the factory. To install the battery, follow the steps below: 1 Pull out the battery holder. The battery door is located on the lower end of the remote. Simply pull the tab to open the battery holder. 2 Position the included lithium coin battery (CR2025) battery so it sits in the battery holder correctly. Make sure the polarity (the + and – sides of the battery) is correct. 3 Replace the battery door. NOTE Please discard used batteries properly. Getting Started Placing and Removing Adapters for the iPhone and iPod Your Altec Lansing inMotion Kick speaker system includes removable adapters for today’s popular iPhone and iPod models. These adapters ensure that your iPhone and iPod properly fit in the speaker system’s dock. As new iPhone and iPod models are introduced, new adapters will be made available to customers. You may also use the adapter supplied with your iPhone or iPod, or available for purchase at How to Place an Adapter 1 Select the correct adapter for your iPhone or iPod. Using the correct adapter ensures a proper fit for your iPhone or iPod. 2 Gently press the iPhone or iPod adapter into the dock. Now you can carefully place your iPhone or iPod into the dock. NOTE Your iPhone or iPod cannot be in a case. How to Remove an Adapter 1 Remove your iPhone or iPod. 2 Grip the adapter and pull gently upward. Speaker Features and Indicators iPod LED AUX LED Battery LED Track forward button Track back button Volume increase button Volume decrease button Source button Power on/off button Power LED Adjustable handle AC adapter jack Universal docking station for iPhone or iPod AUX jack Speaker Controls Turn on your speaker system Ensure the AC adapter is connected to the system and plugged into the wall. See the Getting Started section for more information. Press the button. Turn off your speaker system Press the button. Whenever you are finished using your speaker system, please remember to turn it and your iPhone, iPod or other MP3 player off to conserve electricity. Change audio source Press the “SOURCE” button to sele...