valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
- STOP/EJECT Preparation: Insert the CD. STOP/EJECT □/6 Press D/A STOP/EJECT and load the tape. ©Load the tape with the side to be recorded facing you. • Either have the leader tape wound up in advance or locate the position where recording is to begin. Set SELECTOR to “CD”: TAPE/ EH3 RADIO CD ■=» Press O IRECI to start recording on the tape. CD play starts simultaneously. Recording stops at the end of the tape. If the tape comes to the end while a track is still being recorded, the track . will be only partially recorded. To continue recording on the other side of the tape, remove the tape, turn it around, install it again, and start recording once more. To stop the recording: / STOP/EJECT □ /A Press D/A STOP/EJECT and □. To stop the recording temporarily: Press 11 PAUSE. To resume recording, press 11 PAUSE again. To take up the leader tape: Magnetic part of tape Leader tape (recording cannot be made) Type of tape which can be used for recording: Normal position/TYPE I O High position/TYPE 11 X Metal position/TYPE IV X This unit can not make a recording or erasing correctly, if high position tapes and metal position tapes are used. Recording your favorite tracks: After step 2, press or »| and display the track number before pressing O i recI to start recording. When the recording is completed, press U/± STOP/EJECT and □. If the unit is brought near a TV set during recording, noise may be recorded due to the effects of the signals from the TV set. Maintain a distance of at least 1.5 meters between the unit and a TV set. For your reference: •Any change made to the volume or tone quality during recording will not affect the recording. • In order to prevent trouble caused by flat batteries, it is recommended that you either supply power to the unit from the household AC outlet or replace all the batteries with new ones when you are recording something which is important to you. 9 Maintenance Technical Specifications □ Maintenance of external surfaces Clean it with a cloth, dampened in a mild solution of soap and water. Do not clean the cabinet with benzine or thinner. Avoid excessive moisture. Avoid spray aerosol type cleaner. Some cleaners contain corrosive chemicals that may cause internal damage and cabinet deformation. □ Tape head care To assure sound quality for recording and playback, be sure to clean the tape heads after approximately every 10 hours of use. 1. Open the cassette compartment cover by pressing D/A STOP/EJECT. 2. Pressing the erase prevention lever down, press O ireci. (Heads will come down.) 3. Clean the shaded portion in the figure below with a cotton swab (or a soft, lint-free cloth) slightly moistened with isopropyl alcohol. Do not use any solution other than alcohol for head cleaning. □ Lens care Open the disc holder and clean the lens with a blower (not included). If the lens is extremely dirty, clean it with a cotton swab. □ Head demagnetization ®ln order to maintain good sound quality, it is recommended that the head assembly be demagnetized when distortion or poor sound quality persists after cleaning the head. If the head assembly becomes magnetized, it could create loss of high end frequency response. «Several types of head demagnetizers are available and may be purchased separately at local electronics supply stores. Follow the instructions that are supplied with the device. • Do not bring any type of metal objects or tools, such as magnetic screwdrivers, in contact with the head assembly. □ Radio Frequency range FM AM E3 CD player Sampling frequency Decoding Beam source No. of channels Wow and flutter 88-108 MHz 525-1705 kHz 44.1 kHz 16 bit linear Semiconductor laser (wavelength 780 nm) 2 channel, stereo Less than possible measurement data □ Tape recorder Track system Recording system Erasing system Monitor system Frequency range (Normal) 4 track, 2 channel, stereo AC bias Multi pole magnet Variable sound monitor 80-10000 Hz □ General Power requirement AC 120 V, 60 Hz, Power consumption; 20 W 9 V (Six “D" size, R20/LR20 batteries) Do not use rechargeable type batteries. 10 cm (4”)x2 Headphones; 2.0 mV 430x161x231 mm ( 161 Vi e" x 6Vte" x 9W) 3.1 kg (6 lb. 13 oz.) without batteries Battery Speakers Output jack Dimensions (WXHXD) ' Weight Note: Specifications are subject to change without notice. Weight and dimensions are approximate. Product Service Do not attempt to remove the cover(s) or repair the unit yourself. Refer servicing to qualified personnel only. Product information For product service, product information or assistance with product operation, refer to the servicenter directory. User memo: DATE OF PURCHASE DEALER NAME_ DEALER ADDRESS TELEPHONE NUMBER 10 Concerning Compact Concerning Cassette Discs Tapes Only compact discs having this mark - COMPACT can be used with this unit. |~jj DIGITAL AUDIO □ To remove a disc from its case Press the center holder and lift the disc holding b...