valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
Prefer servicing to qualified service personnel. • DANGEROUS VOLTAGE: Uninsulated dangerous voltage that may be of sufficient magnitude to constitute a risk of electrical shock to persons is present within this product enclosure. • ATTENTION: The owner's manual contains important operating and maintenance instructions. For your safety, it is necessary to refer to the manual. Power supply and connection BATTERY OPERATION • Set the FUNCTION switch to the TAPE position. • Open the battery compartment cover. • Insert 6 batteries (UM-1 or D). Please observe correct battery polarities or the set will not work. 2 • Close the battery compartment cover. AC OPERATION • Before the first connecting of the appliance check that voltage indicated on the rating label corresponds the mains voltage in your home. • Plug the corresponding end of cord into the AC socket on the rear of the set. • Insert the plug into power supply. CAUTION: • When the set is only used with AC or is not used for 2 weeks or more, please remove the batteries, to avoid damage to the set from leakage of batteries. • Always unplug the appliance from power supply, when no use long time. • This unit cannot be operated by batteries if the AC power cord is connected to the unit. HEADPHONE CONNECTING • For private listening, insert 3.5 mm headphones into the stereo headphone jack. • Slide volume control switch to the appropriate level as desired. • When the stereo headphone jack is plugged, speaker will disconnect automatically. Function FUNCTION SWITCH • Position to RADIO for: -Radio reception -Cassette recording from the radio • Position to TAPE for: -Cassette playback Sound adjustment VOLUME The level of sound reproduced by the loudspeaker or Stereo Headphones is adjusted by the VOLUME control. NOTE: During recording, adjusting the VOLUME control only affects the monitor sound and not the content of recording. 3 Radio operation OPERATION • Set Function switch to RADIO position thus the Power LED indicator should light up. • Select your desired broadcasting band with Band switch. • Rotate the Tuning control regulator to receive the desired broadcast. • Adjust the level of sound with Volume control switch. • To turn off the radio, set the Function switch to TAPE position. ANTENNA • For FM reception, adjust the telescopic antenna to obtain the best reception on the band selected. • The AM signals are picked up through the built-in ferrite antenna. The set should be placed to a position for the best reception. CAUTION: • Do not connect FM antenna to an external antenna. FM AND FM STEREO RECEPTION Set the FUNCTION switch to the FM STEREO position. This is the ideal setting to listen to FM Stations as it will provide Stereo Sound. If the reception is weak, the FUNCTION Switch can be set to FM MONO. The reception will be stronger but the quality of sound will not be that of FM STEREO. Cassette recorder operation CONTROLS • STOP/EJECT button During operation, depress to stop all deck operation. Press again to open the cassette door. • FAST FORWARD button and REWIND button Press to rapidly advance the tape in either forward or reverse direction. • PLAY button Press to start playback. • PAUSE button Press to stop tape operation temporarily. Press again to resume tape operation. • RECORD button Press to start recording. PLAY button will be activated automatically. 4 CASSETTE PLAYBACK • Slide the Function switch to TAPE position thus the Power LED indicator should light up. • Press the STOP/EJECT button to open the cassette compartment. • Insert a cassette with tape side upward and push the cassette door to close the cassette compartment. • Press the PLAY button to start the playing. • Adjust the VOLUME control to the desired sound level. Recording RECORDING FROM RADIO • Slide the Function switch to RADIO position thus the Power LED indicator should light up. • Tune to the desired station by turning the Tuning control regulator. • Insert a blank cassette into cassette compartment with tape side upward. • Press the PLAY button and RECORD button simultaneously to start recording. • Press the STOP/EJECT button when finished. NOTE: • You may want to monitor playback during recording. You can adjust the sound with the VOLUME control. This adjustment does not affect the content of recording Special features AUTOMATIC STOP • During playback or recording, the unit will shut itself off automatically at the end of tape. AUTOMATIC RECORDING LEVEL CONTROL (ALC) • The unit incorporates with built-in ALC circuitry which automatically adjust the optimum recording level without overloading during recording or dubbing. 5 Maintenance and care • Check your batteries regularly, old or disch...