valutazioni - 0, GPA: 4
(
)
)
|
Foto e specifiche JVC KS-FX942R |
Facilità d'uso
(PSM: see page 26.) 2 Press . or 4 to select “B.SKIP” (blank skip). 3 Turn the control dial clockwise to select “ON.” Now Blank Skip is activated. 4 Finish the setting. To cancel Blank Skip, repeat the same procedure and select “OFF” in step 3 by turning the control dial counterclockwise. ENGLISH 21 22 ENGLISH Prohibiting cassette ejection You can prohibit cassette ejection and lock a cassette in the cassette compartment. While pressing TAPE CD-CH, press and hold for more than 2 seconds. “NO EJECT” flashes on the display for about 5 seconds, and the cassette is locked and cannot be ejected. To cancel the prohibition and unlock the cassette While pressing TAPE CD-CH, press and hold again for more than 2 seconds. “EJECT OK” flashes on the display for about 5 seconds, and the cassette is unlocked. Note: If you press 0 while cassette ejection is prohibited, the control panel flips down, but the cassette continues to play and cannot be ejected. Playing the current tune repeatedly You can play the current tune repeatedly (Repeat Play). 1 Press MODE to enter the functions mode while playing a tune you want to hear over again on a cassette. “MODE” flashes on the upper part of the display. 2 Press RPT (repeat), while “MODE” is still on the display, so that “REPEAT” appears on the display. When the tune has been played, the tape is automatically rewound to the beginning of that tune and the same tune will be played again. To cancel Repeat Play, repeat steps 1 and 2 again so that the RPT indicator goes off. Note: In the following cases, Blank Skip and Repeat Play may not operate correctly: – Tapes with tunes having long pianissimo passages (very quiet parts) or non-recorded portions during tunes. – Tapes with short non-recorded sections. – Tapes with high level noise or humming between tunes. – Tapes with tunes recorded at low recording levels. – The Dolby NR setting does not match. For example, if Dolby B NR is on and the tape was recorded with no Dolby NR. Lights up when Repeat Play is turned on. SOUND ADJUSTMENTS Selecting preset sound modes (C-EQ: custom equalizer) You can select a preset sound mode (C-EQ: custom equalizer) suitable to the music genre. • There is a time limit in doing the following procedure. If the setting is canceled before you finish, start from step 1again. 1 Press MODE to enter the functions mode. “MODE” flashes on the upper part of the display. 2 Press EQ (equalizer), while “MODE” is still flashing on the display. The last selected sound mode is recalled and applied to the current source. Indication For: Preset values BAS TRE LOUD USER (Flat sound) 00 00 OFF ROCK Rock or disco music +03 +01 ON CLASSIC Classical music +01 –02 OFF POPS Light music +04 +01 OFF HIP HOP Funk or rap music +02 00 ON JAZZ Jazz music +02 +03 OFF Note: You can adjust each sound mode to your preference. Once you make an adjustment, it is automatically stored for the currently selected sound mode. See “Adjusting the sound” on page 24. ENGLISH Sound mode indicator flashes. Ex.: If you have selected “USER” previously 3 Select the sound mode you want. Each time you press the button, the sound modes change as follows: CLASSIC JAZZ USER ROCK HIP HOP POPS Sound mode indicator flashes. Ex.: When you select “ROCK” 23 ENGLISH Adjusting the sound You can adjust the sound characteristics to your preference. 1 Select the item you want to adjust. Each time you press the button, the adjustable items change as follows: BAS TRE FAD (bass) (treble) (fader) VOL LOUD BAL (volume) (loudness) (balance) Indication To do: Range BAS*1 Adjust the bass. –06 (min.) | +06 (max.) TRE*1 Adjust the treble. –06 (min.) | +06 (max.) FAD*2 Adjust the front and rear speakerbalance. R06 (Rear only) | F06 (Front only) BAL Adjust the left and right speakerbalance. L06 (Left only) | R06 (Right only) LOUD*1 Boost low and high frequencies to produce a well- balanced sound at low volume level. LOUD ON | LOUD OFF VOL*3 Adjust the volume. 00 (min.) | 50 (max.) 2 Adjust the setting. To increase the level or turn on the loudness To decrease the level or turn off the loudness Equalization pattern changes as you adjust the bass or treble. Ex. 1: When you adjust “TRE” (treble) Ex. 2: When you turn on the loudness 3 Repeat steps 1 and 2to adjust the other items. To reset each sound mode to the factory settings, repeat the same procedure and reassign the preset values listed in the table on page 23. *1 When you adjust the bass, treble, or loudness, the adjustment you have made is stored for the currently selected sound mode (C-EQ) including “USER.” *2 If you are using a two-speaker system, set the fader level to “00.” *3 Normally the control dial works as the volume control. So you do not have to select “VOL” to adjust the volume level. 24 OTHER MAIN FUNCTIONS Changing the general settings (PSM) You can change the items listed on the next page by using the PSM (Preferred Setting Mode) control. Basic Procedure 1 Press and hold SEL (select) for more than 2 seconds so that ...