valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
continued
The remote does not function.
To demagnetize the tape heads
The batteries have run down.
After 20 to 30 hours of use, enough residual
Replace both batteries.
magnetism will have built up on the heads
CD Player
There is an obstacle between the
to begin to cause loss of high frequencies
remote and the system. Remove the
and hiss. At this time, demagnetize the
obstacle.
heads and all metal parts in the tape path
The disc tray does not close.
with a commercially available tape head
The CD is not placed correctly.
demagnetizer. Refer to the instructions of
the demagnetizer.
The CD will not play.
Restoring the Factory
The CD is dirty.
Settings
To clean the cabinet
The CD is inserted label side down.
Use a soft cloth slightly moistened with
The player is in pause mode.
mild detergent solution.
Moisture condensation has builtup.
Unplug the mains lead and then plug it
Leave the system turned on for
back into the wall outlet.
To clean the CD
about an hour until the moisture
Keep DISPLAY and FUNCTION pressed
When a CD is dirty, clean it with a cleaning
evaporates.
and press TAPE.
cloth. Wipe the CD from the centre out.
Play does not start from the first
Notes on CD
track.
•Do not use solvents such as benzene,
The CD player is in programme or
thinner, commercially available cleaners,
shuffle mode. Press PLAY MODE
or anti-static spray intended for vinyl LPs.
repeatedly so that “PROGRAM” or
Maintenance
•If there is a scratch, dirt or fingerprints on
“SHUFFLE” disappears.
the CD, it may cause a tracking error.
“
” is displayed.
To clean the tape heads and tape
) on the unit was repeatedly
path
pressed at the end of the CD. Turn
Contaminated tape heads cause poor
the jog dial counterclockwise (or
recording or sound drop-out in playback.
GB
press = on the remote) to return
We recommend cleaning after every 10
hours of operation.
22
to the normal display.
Specifications
Open the tape compartment and wipe the
CD player section
heads, the pinch rollers and the capstans
with a cleaning swab slightly moistened
System
Compact disc digital audio
with cleaning fluid or alcohol. Wipe the
system
General
parts shown below.
Laser
Semiconductor laser (λ =
780 nm)
There is no sound.
Deck A
Emission duration:
Press VOLUME +.
continuous
The headphones are connected.
Cleaning swab
Laser output
Max 44.6 µW*
Disconnect them.
Capstan
* This output is the value
measured at a distance of
Sound comes from one channel or
200 mm from the
unbalanced left and right volume.
objective lens surface on
Check the speaker connections of
the Optical Pick-up Block
the inoperative channel.
with 7 mm aperture.
Wavelength
780 – 790 nm
The left and right sound are
Pinch roller
Frequency response
reversed.
Playback head
2 Hz – 20 kHz
Check the speaker connection and
Signal-to-noise ratio
speaker placement.
Deck B
More than 65 dB
Dynamic range
Bass is lacking or the location of the
Cleaning swab Erase head
More than 97 dB
musical instruments is apparently
Capstan
imprecise.
Tuner section
Check the speaker connection for
FM stereo, FM/AM superheterodyne tuner
proper phasing.
FM tuner section
There is severe hum or noise.
Tuning range
87.5 – 108.0 MHz (50 kHz
TV or VCR is too close to the stereo
step)
system. Move the stereo system
Pinch roller
Aerial
FM lead aerial
away from the TV or VCR.
Record/playback head
Aerial terminals
75 ohm unbalanced
“0:00” flashes in the display.
Insert a tape when the areas cleaned are
Intermediate frequency
A power interruption occured.
completely dry.
10.7 MHz
Set the clock and timer settings
again.
For Your Information
...