|
Facilità d'uso
A spare parts listing is also provided, and parts are readily available by following the instructions as detailed on the back page of this manual. SAFETY INSTRUCTIONS 1. Do Not operate the unit when vou are fatiqued. 2. Do Not ODerate if other people or animals are in the work area 3. Do Not ooerate the unit without the shield correctly in position. 4. Do Not operate in a confined area. Carbon monoxide exhaust aas is hiahlv ooisonous. 5. Do Not ooerate the unit while vou are smokinq. 6. Always wear eye protection goodies when operatinq the unit. 7. Always hold the unit firmlv with both hands and with firmer s and thumbs encirclina the handles. 8. Always obev local ordinances reaulatino the use of internal combustion enames in vour area. 9. Always use the cutting attachments as approved and suDDlied bv ECHO Inc. for vour unit. 10. Always remain alert when operating the unit to avoid Dossible iniurv to vourself and other people. WARNING-DANGER 1. Do Not smoke while handlina Gasoline. 2. Do Not refuel a hot engine. Wait until it cools. 3. Do Not overfill the tank. Soilied fuel must be wiDed up. 4. Always stop the engine when refueling. 5. Always remove the fuBl cap slowly in order to relieve anv pressure build ud in the tank. 6. Always restart the engine at least 10 feet awav from the refuelina point. 7. Always store gasoline in an approved container. — 1 — CONTENTS Page Safety Instructions........................................................................................... 1 Technical Data................................................................................................. 2 Nomenclature of Parts ....................................................................................... 3 Assembling.................................................................................................... 3 Nylon Cord Cutter Head...................................................................................... 5 • Installation............................................................................................. 5 • Adjustment............................................................................................. 5 • Replacement.......................................................................................... 6 Operation...................................................................................................... 7 Maintenance and Care........................................................................................10 Trorage Shooting.............................................................................................12 Storage After Use................................................ ............................................13 Parts Catalogue...............................................................................................14 TECHNICAL DATA GT-140 B GT-160 GT—200 A Dimension LxWxH cm (in.) 147x17x37(57.9x6.7x14.6) 147x19x37 (57.9x7.5x14.6) Weight kg (lbs] 4.8 (10.6): w/o cutter head 5.0 (11.0) : w/o cutter head Engine Type Displacement Max. revolution Carburetor Ignition Spark plug Starter Clutch cc (cu.in.) rpm Air cooled two stroke single cylinder 13.8(0.84) 16.0 (0.97) 21.2(1.29) 6500 7000 7500 Walbro diaphragm type WA Flywheel magneto: Contact braker point system NGKBM6A Recoil starter Automatic centrifugal clutch Fuel Mixing ratio Tank capacity Mixture of regular gasoline and air cooled two stroke engine oil. [20:1 Ratio or 32:1 Ratio with special oil approved by ECHO] litre (FL.OZ.US) 0.25(8.5) 0.5 (16.9) Drive shaft ass'y Cutter (Nylon cord cutter head) Manual Semi-automatic Cutting swath 14 in. j Cutting swath 16 in. Bearing Rotation Lubrication Drive shaft Shield Two Ball Bearings Clockwise Shell Delpena or good quality lithium based grease Flexible high tensile steel Plastic shield mounted on the bearing housing (with replaceable cut-off knife) Technical data subject change without notice. - 2 NOMENCLATURE OF PARTS Spark plug Cylinder Muffler Carburetor Fuel tank •Cutter head •Bearing housing i- Drive shaft ass y Loop handle Ignition switch Shield Throttle trigger ENGINE ASSEMBLING DRIVE SHAFT • Stand engine upright on a level floor • Loosen bolt at drive shaft end of the engine. • Fit drive shaft assembly ensuring that the drive shaft is correctly engaged • The line on drive shaft housing must be in contact with the engine. • Rotate drive shaft housing until gear housing is in line with the engine • Tighten bolt to fasten drive shaft ass'y. L- Insert to this line^ THROTTLE CABLE As the engine is delivered with throttle cable (engine side) separated, assemble the cable to carburetor as follows • Remove nut (A) and ond one washer from throttle cable. • Fit the terminal of the ignition switch wire (ground lead) on the cable ad|uster before following steps. • Insert throttle cable through the hole of fancover as shown. ...
Questo manuale è adatto anche per i modelli :Clippers - GT-140B (1.03 mb)
Clippers - GT-200A (1.03 mb)