valutazioni - , GPA:
(
)
)
Produttore : Echo
File Size : 435.11 kb
File Nome : 8fd1b519-8f5e-4634-357f-5594436205ed.pdf
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
Facilità d'uso
5. RAPID LOADERTM HEAD - Contains replaceable nylon trimming lines. 6. PLASTIC DEBRIS SHIELD ASSEMBLY - Included in plastic bag (co-pack). MUST be installed on unit before use, see Assembly Instructions. Shield assembly includes the Cut-Off Knife. Mounts on the Gear Housing Assembly just above the cutting attachment. Helps protect the operator by deflecting debris produced during the trimming operation. 7. CUT-OFF KNIFE -Trims line to the correct length. 8. THROTTLE TRIGGER - Spring loaded to return to idle when released. During acceleration, press trigger gradually for best operating technique. 9. STOP SWITCH - "TOGGLE SWITCH" mounted on the engine. Move switch UP to RUN, DOWN to STOP. 10. ARM REST - Provides arm rest during operation and protects arm from hot engine. 11. MUFFLER SPARK ARRESTOR - The muffler controls the exhaust noise while the spark arrestor prevents hot particles of carbon from leaving leaving the muffler where they could possibly start a fire. 12. FUEL TANK- Contains fuel and fuel filter. 13. RECOIL STARTER HANDLE - Pull handle slowly until recoil starter engages, then quickly and firmly. When engine starts, return handle slowly. DO NOT let handle snap back or damage to unit will occur. 14. FUEL TANK CAP - Cover and seals fuel tank opening. 15. PRIMER BULB - Pumping primer bulb before starting engine draws fresh fuel from the fuel tank priming the carburetor for starting. Pump primer bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5 times. 16. AIR CLEANER - Contains replaceable filter element. 17. CHOKE - Located above the air cleaner housing. Controls operation of choke. Move choke to starting position (Close Choke) and back to run position (Open Choke). 18. SPARK PLUG - Provides spark to ignite fuel mixture. 19. SAFETY VIDEO - (Not included with unit) P/N 99922202540 English version only is available at a cost of $5.00 from ECHO, INC. or any authorized ECHO dealer. The video overviews safety precautions and proper operating techniques and is supplemental to the Safety Manual. Read and understand the Safety Manual for complete information on safe operation. GRASS TRIMMER OPERATOR'S MANUAL 9 SPECIFICATIONS MODEL GT-2000R Length 1400 mm (55.1 in.) Width 330 mm (13.0 in.) Height 360 mm (14.2 in.) Weight (dry) w/Cutter Head 4.08 kg (9.0 lb.) Engine Type Air cooled, two-stroke, single cylinder gasoline engine Bore 32.2 mm (1.268 in.) Stroke 26.0 mm (1.04 in.) Displacement in.)21.2 cc (1.29 cu. Exhaust System Spark Arrestor Muffler Carburetor Zama diaphragm model C1U w/primer SystemIgnition magneto, capacitor dischargeFlywheel Spark Plug Gap 0.65 mm (0.026 in.)NGK BPM-7A Fuel Mixed (Gasoline and Two-stroke Oil) Fuel/Oil Ratio 50:1 ECHO High Performance, two-stroke air cooled engine oil Gasoline use fuel containing methyl alcohol, moreDO NOT89 Octane unleaded. 10% ethyl alcohol or 15% MTBE.than Oil 50:1 ECHO High Performance, two-stroke air cooled engine oil Fuel Tank Capacity oz.)(13.5 US fl.0.4 lit. Starter System Automatic Rewind Starter Clutch Centrifugal Type Drive Shaft ShaftFlex1/4" Rotating Direction Clockwise viewed from top Cutter Head .080 Line capacity 203 mm (8 in.)line head (2-line) withNylon Handle Grip-D-Loop, Right-Left Shoulder Harness Optional P/N 99944200201 Idle Speed (RPM) 3200 RPM-2400 .)Throttle Speed (W.O.TWide Open Line Head (RPM)with Nylon 7500 RPM-6800 10 10 NYLON LINE HEAD Tools Required: Head Locking Tool Parts Required: Rapid LoaderTM Head. 1. Remove plastic threaded shaft sleeve and adapter plate from PTO shaft. 2. Align locating hole in upper plate with hole in bearing housing and insert 1/8 in. diameter locking tool (A). 3. Place large washer then line head on threaded shaft followed by small metal washer and locknut. 4. Tighten locknut securely. IMPORTANT Remember to remove the locking tool. ASSEMBLY Tools Required: None PLASTIC SHIELD 1. Snap the shield over the bearing housing. 2. Install bolt (A), washer (B) and wing nut (C). A GRASS TRIMMER OPERATOR'S MANUAL 11 NYLON LINE INSTALLATION Level1. Tools Required: None Parts Required: Two (2) Pre-cut Nylon Line 8 in. X .080 in. 1. Shut engine off. Lay unit on the ground with head assembly up. 2. Remove old nylon line through center recess of head. 3. Thread new lines through outside holes (A) in housing until ends meet in center of recess. NOTE Insert cutting line ends to center of head recess to insure easy removal of used lines. A FRONT (LOOP) HANDLE NOTE Front handle is pre-installed. Re-positioning and tightening is all that is required. 1. Position front handle (E) in comfortable operating position and tighten wing nut (F). The cutting attachment should be 5-7.5 cm (2-3 in.) above the ground and as level as possible. 12 12 PRE - OPERATION FUEL Fuel Requirements R + M 2 Gasoline -Use 89 Octane [ ] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to 15% MTBE (methyl tertiary-butyl ether). Gasohol containing methyl (...