valutazioni - 2, GPA: 3.5
(
)
)
|
Facilità d'uso
6. Rotate locator pin (A) 1/4 turn clockwise to engage lower shaft hole. Insure locator pin is fully engaged by gently twistinglower drive shaft. Locator pin (A) should snap flush in coupler. Full engagement will prevent further shaft rotation. 7. Secure lower shaft assembly to coupler by tightening clamping knob (D). C E D A PLASTIC SHIELD INSTALLATION (for Nylon Line Operation) NOTE The plastic shield is for use with the Nylon Line Head only. Install Metal Shield when using plastic or metal blades. 1. Remove plastic threaded shaft sleeve and adapter plate (C) from PTO shaft (A). 2. Place the shield on the bottom of the bearing housing flange. 3. Place shield plate (B) on shield, align holes. Install three (3) screws from bottom through plate and shield into gear case. 4. Assemble upper plate (C) onto PTO shaft. A B C PAS RAPID LOADERTM TRIMMER ATTACHMENT OPERATOR'S MANUAL 9 NYLON LINE HEAD INSTALLATION 1. Align hole in upper plate with notch in edge of gear housing and insert head locking tool (A). Remove plastic sleeve from PTO shaft. 2. Be sure upper plate (B) remains on PTO shaft. 3. Place line head onto PTO shaft, followed by large metal washer (C). 4. Thread L.H. nut (D) on PTO shaft. Tighten securely. 5. Install new split pin (E). 6. Remove locking tool (A). C OPERATION NOTE Refer to your Split Boom\Pro Attachment SeriesTM Operator's Manual for correct engine fueling, starting and stopping instructions. IMPORTANT Never wear line shorter than 1-1/2 inch extension from head, otherwise overspeeding and engine damage may result. 10 MAINTENANCE Your ECHO trimmer is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your trimmer achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed see your ECHO dealer for repairs. SKILL LEVELS Level 1 = Easy to do. Most required tools come with unit. Level 2 = Moderate difficulty. Some specialized tools may be required. Level 3 = Experience required. Specialized tools are required. MAINTENANCE INTERVALS Component/System Maintenance Procedure Skill Level Frequency Drive Shaft Grease 1 Every 25 hours of use Gear Housing Grease 1 Every 50 hours of use Screws/Nuts/Bolts Inspect/Tighten/Replace 1 Before each use LUBRICATION Level1. Tools Required: 8 mm Open End Wrench, Screwdriver, Clean Rag. Parts Required: ECHO® LUBETM 8 oz. (P/N 91014) or Lithium Base Grease. Gear Housing 1. Clean all loose debris from gear box. 2. Remove plug (A) and check level of grease. 3. Fill gear case with grease. 4. Install plug (A). Drive Shaft (Lower) A IMPORTANT Lower and upper drive shaft must be lubricated with ECHO® LUBETM grease every 25 hours of operation, otherwise drive shaft assembly overheating and failure can result. PAS RAPID LOADERTM TRIMMER ATTACHMENT OPERATOR'S MANUAL 11 1. Loosen two (2) 8 mm upper gear housing bolts (B) and locator B C screw (C). Remove gear case assembly. 2. Remove flex cable, wipe clean and apply a thin coating 15 ml, of grease. 3. Install flex cable. Make sure cable end engages upper drive shaft adaptor. 4. Install gear case assembly onto drive shaft aligning locator screw with hole in drive shaft. 5. Tighten two 8 mm bolts (B) and locator screw (C). D IMPORTANT Flat edge of washers (D) must be against drive shaft. NYLON LINE REPLACEMENT Level1. Tools Required: None Parts Required: Pre-cut Nylon Line MODELS REQUIRED LINE SIZES SRM-2100SB SRM-210SB/211SB .080 - .095 in. PAS-210/211 PAS-230/231 SRM-2400SB .095 - .130 in. SRM-260SB/261SB .095 - .155 in. PAS-2601 .095 - .155 in. PAS-260/261 .095 - .155 in. 1. Insert pre-cut 204 mm (8 in.) length of nylon cutting line (recommended sizes 2.4 mm [.095 in.] to 3.9 mm [.155 in.]) through outside openings of trimmer head. Minimum of 153mm (6 in.) of line should extend from each opening. 3.9mm [.155 in.] line not recommended for trimmers under 26cc. NOTE Insert cutting line ends to center of head recess to insure easy removal of used lines. NOTICE: Nylon line can damage plastic shield. When installing line segments, make sure line does not curve upward toward shield. 12 STORAGE Storage Hook Installation 1. Insert small end of hook into locating hole on attachment shaft. 2. Slide plastic cap onto end of attachment shaft. SPECIFICATIONS PAS Rapid LoaderTM Attachment Shaft Length------------------------------------------------838 mm (33 in.) Attachment Width-----------------------------------------178 mm (7 in.) Attchment Height------------------------------------------229 mm (9 in.) Weight (dry) w/blade --------------------------------------1.36 kg. (3.1 lb.) Drive Shaft --------------------------------------------------6.35 mm (1/4 in.) Flex Shaft Rotating Direction -----------------------------------------Counter-clockwise viewe...
Questo manuale è adatto anche per i modelli :Clippers - 99944200610, SRM-2100SB, SRM-2400SB, SRM-210SB, SRM-211SB, SRM-260SB, SRM-261SB, PAS-2100, PAS-2400, (214.45 kb)