valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
Always hold your hand protected by the blade guard. This is facilitated by the use of a long box spanner. The illustration shows the area in which you should keep the box spanner. I H L A G F D B C 20 – English English – 21 ASSEMBLY Assembling the spray guard and trimmer head Superauto II (225R/RD, 227R/RD, 232R/RD) K J I G F I M L A K B C • Fit the guard (A) intended for use with the trimmer head. Secure using the 4 bolts (L) and the support plate (M) as set out in the diagram. • Fit the drive disc (B) on the output axle. • Turn the blade axle until one of the holes in the drive disc aligns with the hole in the gear housing. • Insert the locking pin (C) in the hole so that the axle is locked. • The trimmer head must be split to be fitted (see the diagram). Proceed as follows: • Insert your finger into the centre hole of the cover (I) at the same time as you hold the cover with your other fingers. Press the two catches (J) that extend from the cut-out on the bottom section (K) using the thumb and index finger of your other hand. Press apart the trimmer head using the fingers on the cover. • Place the cover (I) and the support flange (F) on the output axle. • Fit the nut (G). The tightening torque of the nut is 35-50 Nm (3,5-5 kpm). Use the socket spanner in the tool kit. Hold the handle of the spanner as close to the trimmer guard as possible. The nut is tightened when the spanner is turned against the direction of rotation (left-hand thread). • Fit the trimmer head‘s bottom section (K) on the cover (I) by pressing the two sections together with the cut-outs on the bottom section aligned with the catches on the cover. • To dismantle follow the instructions in the reverse order. Assembling the spray guard and trimmer head Trimmy SII (235R) • Fit the guard (A) intended for use with the trimmer head. Secure using four bolts (L) and the support plate (M) as shown in the diagram. • Fit the driver plate (B) on the drive shaft. • Rotate the drive shaft so that one of the holes in the driver plate lines up with the corresponding hole in the gear housing. • Insert the locking pin (C) into the hole to lock the shaft. • Screw on the trimmer head (H) in the opposite direction to the normal direction of rotation. • Tighten the trimmer head to a torque of 35-50 Nm (3.5-5 kpm). • To remove the trimmer head just reverse the sequence. • Fit the guard (A) intended for use with the trimmer head. Secure using four bolts (L) and the support plate (M) as shown in the diagram. • Fit the disc drive (B) on the output axle. • Turn the blade axle until one of the disc drive’s holes aligns with the corresponding hole in the gear housing. • Insert the locking pin (C) into the hole to lock the axle. • Screw on the trimmer head (H) in the direction of rotation. • Dismantling takes place in the reverse order. B A L M C H H B A L M C Assembling other guards and cutting equipment ASSEMBLY Assembling and dismantling the two-part shaft (225RD, 227RD, 232RD) Assembling: • Make sure the handle is loose. • Guide the cut-out on the lower section of the shaft into the coupling‘s locking plate on the upper section of the shaft. The sections are then locked together. • Tighten the handle. Dismantling • Undo the handle (at least three turns). • Press the handle towards the coupling. • Carefully twist the lower section out of the lock. • Hold both parts of the shaft and pull out the lower section from the coupling. Adjusting the harness and clearing saw ! ! WARNING! When working with the clearing saw it should always be hooked in the harness. If this is not done, you cannot control the clearing saw safely and this can result in injury to yourself or someone else. Never use a harness with a defective quick release catch. Quick release On the front is an easily accessible, quick release catch. Use this if the engine should catch fire or in any other emergency situation when you quickly need to take off the harness and machine. Even load on the shoulders A well-adjusted harness and clearing saw significantly facilitates working. Adjust the harness for the best working position. Tension the side straps so that the weight is evenly distributed across the shoulders. Correct height 1) Forestry clearing Adjust the carrier strap so that the suspension hook comes approximately 10 cm under the hip. The blade should be angled forward a little. 2)Grass clearing The suspension hook should hang approximately 20 cm under the hip so that the blade is parallel to the ground. Correct balance 1)Forestry clearing Move the suspension eye forwards or backwards. If the blade is balanced a 1020 cm above the ground it is easier to avoid stones. 2)Grass clearing Let the blade balance at a comfortable clearing height, i.e. close to the ground. 22 – English FUEL HANDLING Fuel mixture NOTE! The machine is fitted with a two-stroke engine and must always be run on a mixture of gasoline and two-stroke oil. It is important to measure the quantity of oil accurately, to ensure the corre...
Questo manuale è adatto anche per i modelli :Clippers - 232R/RD 235R (1.42 mb)