valutazioni - 2, GPA: 3.5 ( )

Produttore : Little Wonder File Size : 484.73 kb File Nome : 02_05_pn_310700.pdf Lingua di insegnamento:

Then loop the bend under the cord retaining clips as shown. This will prevent the extension cord from detaching from the hedge trimmer plug. Misuse of this Hedge Trimmer will void the warranty. ie: cutting hedges or shrubs over 1/2" in diameter or foreign objects such as wires, rocks, or fences. Before trimming check work area for foreign objects such as wires, cords, glass, fences, or rocks. Be sure to remove any foreign objects from the work area. Failure to properly maintain this hedge trimmer will void the warranty. 1. Read care and safety instructions carefully before extension cord over hedge being trimmed. On 120V attempting to use this trimmer. Only after you are units, use 16 gauge wire extension cord up to 100 feet. familiar with your hedge trimmer and all of its controls Over 100 feet use 14 or heavier gauge wire or extension and the functions should you start the trimmer. cord. Cords are available from your local Little Wonder dealer. The use of light gauge lamp cords or sizes lighter 2. Before plugging into an electric circuit, be sure that the than those specified above will result in loss of power, voltage supply is as specified on hedge trimmer. possible motor failure, overheating of cord and the Models 1910, 1920, 2410, 2420, 3010, 3020 are rated at possibility of fire. 464 watts at 115 volts. Models 1912, 1922, 2412, 2422, 3012, 3022 are rated at 6. Warning! These trimmers have been designed so they 390 watts at 230 volts. can only be operated when using both hands. Do not attempt to override this important safety feature in any 3. Be sure the switches are in the “off” (not depressed) way. position before connecting unit to the applicable current. (120V AC or 220V/240V AC.) Do not carry a 7. Hold trimmer firmly. For Single Edge Model, keep right plugged -in trimmer with a finger on the switch. hand on side handle and left hand on rear handle. For Double Edge Model, you can place either hand on either 4. The electricity for this hedge trimmer should be handle. Squeeze both switches. supplied through a Residual Current Device (RCD) with Tilt trimmer so cutting tooth is angled slightly toward a tripping current of not more than 30 mA. These the hedge or shrub and proceed to cut. Use protective devices are also known as Residual Current overlapping sweeping motions away from your body to Circuit Breakers (RCCBs) or Earth Leakage Circuit achieve a safe and even cut. The unit is designed Breakers (ELCBs). to cut any type of hedge or shrub; however, thickness of cut should not exceed 1/2 inch 5. Keep extension cord behind trimmer. Never drape in diameter. 1/2" V. MAINTENANCE Remove the plug from the socket before carrying out any adjustment, servicing, or maintainence. A. LUBRICATION AND MAINTENANCE 4. Gear housing and motor bearings have been 1. A few drops of light (#10) oil should be placed on permanently lubricated with a special grease the back edge of each blade at each adjusting which should last for the life of the trimmer. When screw after approximately every four hours of blades are replaced, or any other time that the normal operation. bottom cover plate is removed, the grease must be checked for proper amount (approximately 3/4 full 2. To obtain trouble free trimming, it is necessary to in the area of the gears), and a new gasket and new keep the blades lubricated and clean. The gum screws must be used to insure proper seating of that collects and builds up on the blades can be cover plate. Use only Lubrico M3-3K9K grease removed with 50-50 mixture of kerosene and #10 (P/N 16-78A) in the gear housing. Lubrico M24M oil. Since a petroleum product can shorten the life (P/N 16-78B) is to be used on the motor bearings. of some plastics, it is necessary to remove excess Lubrico is available through your local Little oil-kerosene mixture from the plastic parts. Blades Wonder Dealer. must be clean before they can be adjusted. Caution! Kerosene and oil are flammable. 5. Before each use, inspect to be sure handles, safety devices and fasteners are secure and in place, and 3. A few drops of light (#10) or 3-in-1 oil should be cord is not frayed. If the supply cord is damaged, it put in the hole indicated on the bottom cover must be replaced by the manufacturer, its service plate. This is necessary only at the beginning of a agent or similarly qualified person in order to day’s operation. avoid a hazard. B. SERVICE MAINTENANCE GUIDE Area Maintenance Frequency Gear Housing Check Grease Monthly Blades Inspect / Clean / Lubricate After Each Use Fasteners Inspect / Tighten / Replace Before Each Use Labels Inspect / Replace Before Each Use Handles Inspect / Replace Before Each Use Guards / Safety Devices Inspect / Replace Before Each Use IMPORTANT-Time intervals shown are maximum. Actual use and your experience will determine the frequency of required maintenance. A. TROUBLE SHOOTING Problem VI. SERVICE 1. Blades don’t cut cleanly. Cause Blades are dull or not adjusted properly. Remedy Have blades sha...

Scarica la tua

Per scaricare, digitare 2 cifre :