valutazioni - 4, GPA: 3.5
(
)
)
|
Facilità d'uso
Use only a power source of the same voltage as indicated on the nameplate of the charger when charging. 6. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 7. Charge the battery at a room temperature of 10°C (5OOF) -4OoC (104OF). 8. Do not charge in place exposed to direct sunlight. 9. Do not allow the charger to get wet. IO. Do not charge inside a box or container of any kind. 11. Do not charge near volatile, flammable material such as gasoline, paint, gas, adhesive, etc. 12. Do not charge on top of paper, carpet, vinyl sheeting, cloth materials, etc. 13. Do not allow anything to cover or clog the charger vents. Do not attempt to insert anything into the vents. 14. Do not charge in dusty place. 15. Stop charging immediately if you notice anything abnormal. Ship or take the charger and the battery to your nearest Makita Service Center or Distributor for checking them. 16. Do not attempt to disassemble or make modifications to the charger. 17. Do not put any metal objects or foreign matter into the inlet of the charger. Short-circuit will occur, causing a burn injury and charger breakdown. SAVE THESE INSTRUCTIONS. Charging Connect the battery to the charger using the adaptor cord. Then plug the charger into the power source. The charging light will illuminate and charging will begin. When the charg- ing light goes out at a certain time, the charging is complete. Unplug the charger. (Note: Refer to the table below for the charging time.) DC122 DC121 122 Approx. 1 hour Approx. 2 hours I 121 I Approx. 2 hours I Approx. 4 hours I Battery-, i-Outiet I CAUTION: Always charge the Makita battery 122 immediately after purchase. 0 Always recharge the Makita battery 122 after use. If the Makita battery 122 has not been used for long periods, charge it for more than the time specified in the table above. (Example: If it has not been used for six months, charge it for approx. one week.) Chargingcontinues even after the charging light goes out. If the battery is left uncharged for more than six months, it may become unchargeable. If the light does not come on within five minutes after you start the charging, the battery may be unchargeable. Ship or take the charger and the battery to your nearest Makita Service Center or Distributor for checking. Installing the grip Attach the grip onto the groove in both sides of the tool and secure with the two screws. Screwdriver ScrewdriverScrewdriver Switch action To prevent the trigger from being acciden- tally pulled, a lock-off lever is provided. To start the tool, slide the lock-off lever in the direction of the arrow and pull the trigger. Release the trigger to stop. -Lock-off lever Switch trigger CAUTION: Before connecting the battery to the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. 0 Do not switch on the tool when someone is nearby or when the blades are contacting something. Connecting the battery to the tool Connect the battery to the tool using the adaptor cord. To prevent the adaptor cord from being accidentally disconnected, hook the cord to both strain relief hooks on the tool and the battery. \ \ .Adaptor cord -Strain relief hook / Strain relief hook Carrying the battery Hook the battery to your waist belt. If the adaptor cord is too long for your work, use the band provided to hold it when you coil it shorter. Operation Do not attempt to cut branches thicker than 8 mm (5/16") diameter with this trimmer. These should first the cut with shears down to the hedge trimming level. Hold the tool firmly with both hands. Switch on the tool without the blades making any contact. Move the tool in front of your body while cutting. To cut a hedge top evenly, it helps to tie a string or cord at the desired hedge height and to trim along it, using it as a reference line. n ing or cord To cut a hedge side evenly, it helps to cut from the bottom upwards. Trim boxwood or rhododendron from the base toward the top for a nice appearance and good job. CAUTION: 0 Keep hands away from blades. Be careful not to accidentally contact a metal fence or other hard objects while trim- ming. The blade will break and may cause serious injury. *When not in use, be sure to cover the blades with the blade guard (blade cover). Ex- posed blades may cause serious injury ifsomeone trips over the tool. MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery is disconnected from the tool before attempting to perform inspection or maintenance. Blade maintenance After use, clean off the blades (both sides) with a stiff brush. Then wipe the blades with a cloth and coat them with light machine oil. CAUTION: Dirt and corrosion cause excessive blade friction and shorten the operating time per battery charge. Storage Do not clean the tool, charger and/or battery with benzine, thinner or cleaning chemi- cals. Cracks and discoloration may be caused. Do not store the tool, charger ...
Questo manuale è adatto anche per i modelli :Clippers - UH303D (755.13 kb)