valutazioni - 2, GPA: 4 ( )

Produttore : Electrolux File Size : 2.08 mb File Nome : Lingua di insegnamento:

Cold engine starting • H1. Move stop switch to the “ON” position. • H2. Depress the safety lever (S), squeeze the accelerator trigger (A) and push the throttle advance forwards (B). Now release the accelerator trigger (A) and then the throttle advance (B). . CAUTION! When the throttle advance is engaged, the head or blade rotates. • H3. Move choke lever (E) to the closed position . • H4. Press the primer bulb (C) several times until you see fuel going back to carburetor through pipe (D). Pull starter rope until engine fires once. • H5. Move choke lever (E) to the open position then pull starter rope until engine fires. Let engine run for a few seconds holding the trimmer. Now disengage throttle advance by pulling trigger completely. Engine will now keep on running at idle speed. Hot engine starting STOP switch on START position I. Trigger on idle position (released). Choke towards (open position ). Press the primer bulb (C) several times until you see fuel going back to carburetor through pipe (D). Pull starter rope. . CAUTION! When the throttle (B) advance is engaged, the head or blade rotates. H6. Engine stopping Press the stop switch moving it to STOP position “0”. . CAUTION! When the engine is switched off rotating parts, blade or nylon string head, will keep on rotating for a few seconds. Hold the machine until all parts come to a standstill. . CAUTION! In an emergency the above mentioned delay in stopping may be shortened by touching blade parallel on the ground. ENGLISH -7 I. Carburetor adjustment Your machine can be equipped with a low emission carburetor. We recommend that you have any adjustment of the carburetor made exclusively by an authorized service center, which disposes of special equipment for ensuring the best performance with the lowest emissions. To adjust the speed to the minimum, turn the screw marked (T) as shown: With the engine running and well warmed up, turn the screw (T) gently clockwise, until the engine rotates at regular speed (stead noise), without the cutting devices in motion. If the cutting devices are moving, turn the screw (T) gently counterclockwise until you obtain the proper adjustment. The correct minimum speed is shown in the instruction manual in the paragraph of technical data. . CAUTION! All the above adjustments should be made with the cutting devices correctly installed. . CAUTION! Start the brush cutter in a flat place. During startup stand in a stable position. Make sure the blade or nylon string head do not touch the ground or any obstacles. The warranty may be invalidated due to erroneous adjustments made by personnel not belonging to authorized service centers. L. Routine maintenance Check periodically to see that all the screws in the machine are securely fastened in place. Replace damaged, worn, cracked or bent blades. Always make sure the blade or nylon string head is correctly installed and the nut holding the blade is tight. L1. Cleaning the air filter (At least every 25 hours of work). A clogged filter causes alteration of the carburetor adjustment, reducing power and increasing fuel consumption, as well as causing difficulties in startup. Open the cover on the filter as shown in the figure by pressing in the point indicated by the arrow for release. Clean the inside of the filter housing thoroughly (fig. L2). The filter can be cleaned using gentle jets of compressed air. For more thorough cleaning it can be washed in soapy water. L3. Gearbox Every 50 working hours add grease for high speed gears in the gearbox, through the hole (C). L4. Spark plug Periodically (at least every 50 hours) remove and clean the spark plug and set the space between the electrodes (0.5/0.6 mm). Replace it if excessively encrusted or, in any case, after 100 working hours. In case of excessive encrustation check the carburetor adjustment, the percentage of oil in the fuel mixture and make sure the oil is of excellent quality and suitable for two-stroke engines. L5. Fuel filter To clean or replace the filter, remove the cap on the tank and take the filter out using a hook or long-nose pliers. Periodically, every season, contact your service center for general maintenance and cleaning of the inside....

Scarica la tua

Per scaricare, digitare 2 cifre :