valutazioni - 3, GPA: 3.7 ( )

Produttore : Electrolux File Size : 6.15 mb File Nome : Lingua di insegnamento:

Replace the reel in its housing and thread the ends of the strings in their bushings. Pull each string so that about 15 cm comes out on each side. Reassemble the nylon string head as shown (fig. H5). If the reel becomes excessively worn, replace it with a whole new reel. I. Techniques for use 1 4 5 6 7 8 9 10 11 12 13 14 16 Wait until the engine is running at minimum speed before moving the Backpack adjustment During adjustment remember that the weight of the machine should be distributed mainly on your hips, while your shoulders serve to balance the load. Respect of these precautions will ensure a better balance and be less tiring for your back. Adjust the shoulder straps so that the belt is at hip height. Fasten the belt and adjust the straps so as to distribute the load and balance the weight of the machine accurately. Fasten the shaft to the backpack. Adjust the fastening belt so that the shaft is in the best position for starting the machine ( 12). Cutting techniques . During the cutting operations, keep the engine running at high speed. After every cutting stage, decelerate the engine to minimum speed as running it at top speed without a load can damage the engine severely. machine from one section to another. The machine is ideal to complete the work of the lawnmover. In fact, it can reach places where a normal lawnmower is unable to go. Cutting and trimming grass borders with the nylon string head Cutting with the nylon string head is suitable for light jobs like trimming borders and cutting the grass around trees. Mowing To prevent damage to your lawn or the cutting mechanism, keep the string parallel to the ground but avoid contact with the terrain. Trimming borders Angle the nylon string head keeping it a short distance from the ground. Cut using the end of the string. Do not press the string against the material to be cut. 8-ENGLISH Drawing out the string During cutting, the nylon string wears naturally causing an increase in the speed of the engine and a reduced cutting capacity. When this happens, to bring out more string bump the head against the ground: release the throttle trigger to reduce the engine speed to less than 8000 rpm. Tap gently on the ground with the button (A) as shown in the figure and the string will come out automatically. Accelerate again. If the string does not come out make sure there is still some left and try again. Thinning grass with the grass cutter blade 2 16 The grass is cut with swinging motions from side to side, maintaining the blade parallel to the ground. During the right to left swing the grass is cut, while the backswing must be made without using the blade. I2. KICKBACK can occur when cutting is done with the risk sector of the blade; we recommend cutting with the rest of the blade. Take care that the cup supporting the blade just grazes the ground. This will prevent the blade from touching the ground. Use of sawtooth blade 2 5 11 16 . Do not attempt to cut trees with a larger than recommended diameter, to prevent the risk of kickback or damage to the blade. The sawtooth blade serves to cut bushes and small trees, with maximum diameter of seven centimeters. Rest the left side of the special shield on the trunk while cutting to limit the risk of losing control of the machine. L. Environmental information This section contains information useful for maintaining the characteristics of ecocompatibility included in the origin design of the machine, and as regards proper use and disposal of oil and fuel. Design In the design stage, care was taken to develop an engine with reduced consumption and low emissions of noise and pollutant exhaust fumes. Use of machine The operations of filling the tank with the fuel mixture should be carried out in such a way as to avoid spilling fuel and contaminating the soil and environment. Periods of prolonged disuse Always empty the fuel tank with the same precautions used in filling it. Disposal Do not dispose inappropriately of the machine when it is no longer usable. Deliver it to an authorized organization for proper disposal in compliance with the regulations in force. M. Troubleshooting table The engine does not start The engine stutters or loses power The machine starts but does not cut properly Make sure the STOP switch is on “I”. . Make sure that the fuel tank is at least 25% full. . . Make sure the air filter is clean. . . Remove the sparkplug, dry and clean it, then return it to its place. If necessary, replace it. . . Change the fuel filter. Contact your supplier. . Follow the correct procedure for assembly of the cutting accessories. . Make sure the metal accessories are sharp, and contact your supplier if necessary. . The engine continues to have problems: contact your authorized supplier ENGLISH -9 N. Declaration of conformity The undersigned, authorized by E.O.P., declares that the following products model: type BC011 BC012 starting from the serial numbers produced from 2003 on, manufactured by E.O.P., Valmadre...

Scarica la tua

Per scaricare, digitare 2 cifre :