valutazioni - 5, GPA: 3.8 ( )

Produttore : Electrolux File Size : 1 mb File Nome : Lingua di insegnamento:

The characteristics of the mixture tend to deteriorate in time, so you should only prepare as much mixture as you are going to need (the use of deteriorated fuel can seriously damage the engine). 14 15 Clean the area around the fuel cap before removing it, to prevent any impurities from contaminating the fuel. Take the cap off the fuel container carefully. Unscrew the cap on the fuel tank and fill it with the necessary quality, using a funnel. During use, to prevent problems in starting the engine again, we strongly recommend that you avoid letting the fuel run out in the tank. Fuel storage 14 15 Store the fuel in a cool, well-ventilated place, in an approved fuel storage container. Never store the engine with fuel in the tank in a poorly ventilated place where the fumes produced by the gasoline could propagate and reach a fire, candle, burner or furnace pilot light, water heater, dryer, etc. Never store excessive quantities of fuel. E. Assembly/disassembly E1. Delta grip 2 3 4 For your safety, fasten the delta handle in front of the label placed on the shaft at a distance of at least 11 cm from the rear grip. The handle should be fastened in a comfortable working position. If you are using sawtooth blades, the grip distance should be moved by at least 36 cm. The safety pole guard should be mounted using the accessories supplied and in the configuration shown in the figure,in contact with the delta handle. E2. Double handled grip (A) The grip (A) can be adjusted to suit the needs of the operator by moving it forward or backward. Loosen the knob, place the handle in the desired position then tighten the knob again. CAUTION! The handle assembly (A) can be E4. Fitting guard on line cutter head and grass cutting blade Adjust and secure double hand clamp by tightening the screws. E3. Double Handle (B) folded parallel to the transmission shaft to and tighten the knob. wise, fold the handle (A) in the desired position Loosen the knob, turn the support, by 90° clock- facilitate transport and storage of the machine. 2 3 4 Fit the safety guard (A) against the gearbox (I) position the lower clamp (G) in the housing under the shield and the upper clamp (F) over the shaft. Insert and tighten the screws (H). ENGLISH - 5 Safety guard extension (exclusively for use E6. Assembly/disassembly of grass cutter with nylon string head) blade The string cutting blade housed in the plas E5. Assembly/disassembly of line cutter head ews are tightened all the way (E) and are not loosened by the vibrations. If necessary, tighten them again). eference notches (C), and fasten with the ews (D), then apply the string cutter blade (L) and fasten it with the screw (E) (Make sure the ect assembly see the illustration on the cover and perform the following sequence of steps: Insert the extension (B) on the safety guard (A) at The extension (B) should be installed only for use with the nylon string head, with the aid of the string cutter blade (L), that regulates the length of the string and thus the cutting diameter. For cor otation speed of the engine and interferes with cutting efficiency, as well as increasing the risk of tic shield will cut the nylon string to optiinjury. mum length; a string that is too long reduces the 2 3 4 10 Apply the nylon string head as shown in the illustration: 1) Protection flange 2) Upper plate 3) Protection (nylon string head B) 4) Nylon string head. Tighten by turning counterclockwise. As you tighten, hold the nylon string head and plate still and insert the wrench or screwdriver supplied in the holes in the plate and gearbox; first turn the plate until the two holes match. Do not use the nylon string head guard extension (H) with metal blades. Assemble blade as illustrated: a) Flange guard - b) Upper cap with blade centering - c) Blade with text and directional arrow facing upwards - d) Lower washer - e) Fixed mower gauge - f) Blade locking screw (length mm 16). If you want to assemble the rotating mower gauge,proceed as illustrated: a) Flange guard - b) Upper cap with blade centering - c) Blade with text and directional arrow facing upwards - d) Lower washer - e) Spacer - f) Rotating mower gauge - g) Blade locking screw (length mm 34,5). Assembly of sawtooth blade and blade guard When using the sawtooth blade, remove the guard for the line cutter head and grass cut- ting blade and replace the flange guard (A) with the sawtooth blade guard (H). Saw tooth blades (24 - 80 tooth) have a central base diametre of 20mm and there- fore require the use of the appropriate size top flange to ensure a correct fit. The part number is detailed in the cutting attachment summary chart. For assembly see figures (E7, E8). 2 3 4 10 2 3 4 10 F. Starting and stopping the engine position with the other starter string ar until you encounter some r cord sharp...

Scarica la tua

Per scaricare, digitare 2 cifre :