valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
When the appliance is fully charged, it has a cordless operating time of up to 35 minutes. Do not charge the appliance for more than 24 hours. The appliance does not run from the mains. You cannot charge the appliance in the stand. Insert the appliance plug into the socket of the appliance and put the adapter in the wall socket (Fig. 2). The charging light on the adapter goes on to , indicate that the appliance is charging (Fig. 3). Note:The charging light does not change colour and does not go out when the appliance is fully charged. Optimising the lifetime of the rechargeable battery -Remove the adapter from the wall socket when the batter y is fully charged (which takes 10 hours). -Do not leave the appliance plugged into the wall socket for more than 24 hours. -Discharge the batter y completely twice a year by letting the motor run until it stops. Then fully recharge the batter y. Attaching/detaching attachments All attachments (cutting element, precision trimmer, micro trimmer, micro shaver and nose/ear hair trimmer) can be attached and detached in the same way. 1 2 To attach the attachment, push it onto the handle (‘click’) (Fig. 4). To detach the attachment, pull it off the handle. (Fig. 5) hair clipping Preparing for hair clipping Make sure that the appliance is fully charged when you star t clipping. It is not possible to run the appliance from the mains. Only use the appliance on clean, dry hair. Do not use it on freshly washed hair. 1 Make sure that the head of the person whose hair you intend to cut is at the same level as your chest. This ensures that all parts of the head are clearly visible and within easy reach. 2 3 Comb the hair in the direction of growth (Fig. 6). Put the cutting element on the handle (see section ‘Attaching/detaching attachments’ in chapter ‘Preparing for use’). Clipping with hair clipping comb 1 2 Slide the hair clipping comb into the guiding grooves on both sides of the handle (‘click’) (Fig. 7). Press the setting selector upwards or downwards to set the desired setting (Fig. 8). The setting indicator on the back of the appliance , shows the selected setting. (Fig. 9) The table shows how long the hair will be after clipping at the different settings. When you clip for the first time, star t at the highest setting (9) to familiarise yourself with the appliance. settings of hair clipping comb Setting Hair length after clipping 1 4mm 2 6mm 3 8mm 4 10mm 5 12mm 6 14mm 7 16mm 8 18mm 9 20mm Tip:Write down the hair length settings you have used to create a certain hairstyle as a reminder for future clipping sessions. 3 4 Switch on the appliance. Move the appliance through the hair slowly. -To clip in the most effective way, move the appliance against the direction of hair growth. -Since all hair does not grow in the same direction, you need to move the appliance in different directions (upward, downward or across) (Fig. 10). -Make sure that the flat par t of the comb is always fully in contact with the scalp to obtain an even result. -Make overlapping passes over the head to ensure that you cut all the hair that needs to be cut. -To achieve a good result with curly, sparse or long hair, use a comb to guide the hair towards the appliance. 5 Regularly remove cut hair from the comb. If a lot of hair has accumulated in the comb, remove the comb from the appliance and blow and/or shake the hair out of it. Contouring without hair clipping comb You can use the appliance without hair clipping comb to clip hair ver y close to the skin (0.6mm) or to contour the neckline and the area round the ears. Be careful when you clip without comb because the cutting element removes every hair it touches. Press the setting selector upwards and pull the comb off the handle. (Fig. 11) 1 2 3 Before you start to contour the hairline round the ears, comb the hair ends over the ears. Tilt the appliance in such a way that only one edge of the cutting element touches the hair ends when you shape the contours round the ears (Fig. 12). Only cut the hair ends. The hairline should be close to the ear. 4 To contour the neckline and sideburns, turn the appliance and make downward strokes (Fig. 13). Move the appliance slowly and smoothly. Follow the natural hairline. Trimming Preparing for trimming Make sure that the appliance is fully charged before you star t trimming. It is not possible to run the appliance from the mains. 1 2 Comb the hair to be trimmed (beard, moustache, sideburns, eyebrows) with a fine comb. Put the cutting element on the handle (see section ‘Attaching/detaching attachments’ in chapter ‘Preparing for use’). Beard trimming with beard trimming comb 1 2 Slide the beard trimming comb into the guiding grooves on both sides of the handle (‘click’) (Fig. 14). Press the setting selector upwards or downwards to set the desired setting (Fig. 15). The setting indicator on the back of the appliance , shows the selected setting. The table shows how long the hair will be after trimming at the different set...