valutazioni - 1, GPA: 5
(
)
)
|
Facilità d'uso
3 Press the ON/OFF Button to turn on the appliance. 4 Tilt the Clipper in such a way that only one edge of the cuttiing element touches the hair ends. Be careful not to trim too much. The hairline should be close to the ear (Fig. 13). 5 To contour the neckline and the sideburns, turn the Clipper and make downward strokes (Fig. 14). NOTE: Move the Clipper slowly and smoothly. Simply follow the natural hairline. 6 Adjust the position of the rotating head to make contouring easier. Shaving TIP: Shaving is easier when the hairs are shorter than 1mm. If the hairs are longer than 1mm, use the cutting element without the comb to pre-cut hairs to the shortest setting. 1 Turn off Clipper. 2 Pull the comb off the rotating head (Fig. 12). 3 Press the release buttons (1) and remove the cutting unit from the handle (2) (Fig. 15). 4 Attach the shaving head by pressing it onto the appliance. You will hear a ‘click’ (Fig. 16). Make sure that the shaving head locks into position properly. 5 Remove the protection cap from the shaving head (Fig. 17). If the shaving head foil shows signs of wear or damage, do not use as injury may occur. Do not use the shaving head until foil has been replaced. 6 Adjust the position of the rotating head to make shaving easier. You can do this before and/or during use (Fig. 18). 7 Place the shaving head on your scalp and start shaving (Fig. 19). NOTE: Make sure that the shaving foil is always in full contact with your scalp. Cleaning w Clean the Clipper after each use. w Always switch Clipper OFF, unplug and remove power supply cord from Clipper before cleaning. w Do not use compressed air, abrasive cleaning agents, scourers or aggressive liquids such as gasoline, acetone or ethereal oils to clean the Clipper and attachments. w Never clean, replace or remove Clipper attachments with motor ON. w Do not apply pressure to shaving head. Do not touch foil with hard objects as this may dent or damage foil or cutters. If damage occurs, replace damaged parts. w Do not use Clipper if foil, cutter or cutting element are damaged or broken as injury may occur. w Use a soft, dry cloth to clean Clipper handle. During Use: w If cut hairs have accumulated in the comb area, remove hairs by shaking, blowing or using cleaning brush provided. Cleaning the Cutting Element and Combs After Each Use: 1 Make sure the Clipper is switched OFF and disconnected from the electrical outlet. 2 Remove any comb attachment (Fig. 12). 3 Blow and/or shake out any hair that may have accumulated in the comb. 4 Rinse the comb under the tap or clean it with the cleaning brush supplied. 5 Apply pressure to the center of the cutting element with your thumb (1) until it releases from the rotating head (2) (Fig. 20) . Be careful that the cutting element does not fall to the floor. 6 Clean the cutting element under the tap or with the brush supplied (Fig. 21). Make sure the cutting element is thoroughly dry before reattaching to Clipper. 7 Clean the inside of the rotating head under the tap or with the brush supplied (Fig. 22). 8 Clean the handle and the adapter with the cleaning brush supplied or with a dry cloth. 9 Insert the notch of the cutting element into the slot on the rotating head and push until the cutting element ‘clicks’ into place (Fig. 23). 4222 002 8312 2 ENGLISH IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be followed, including the following: Read all instructions before using this appliance. DANGER To reduce the risk of electric shock: 1. Do not reach for a clipper that has fallen into water. Unplug immediately. 2. Use clipper only in dry condition. Do not use while bathing or in a shower. 3. Do not submerge clipper in water. 4. Do not place or store clipper where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid. 5. Always unplug this clipper from the electrical outlet immediately after using, except when clipper is (re)charging. 6. Unplug and remove power supply cord from clipper before cleaning. 7. The batteries used in this device may present a fire or chemical burn hazard if mistreated. Do not disassemble, heat above 100°C (212°F) or incinerate. WARNING To reduce the risk of burns, fire, electric shock or injury to persons: 1. Close supervision is necessary when this appliance is used by, on, or near children or invalids. 2. Use this clipper for its intended household use as described in this manual. Do not use attachments not recommended by Philips Electronics North America Corporation. 3. Never operate this clipper if it has a damaged cord or plug, if it is not working properly, if it has been dropped, damaged, or dropped into water while plugged in. For assistance call 1-800-243-3050. 4. Clipper can be rinsed under running tap water. Do not operate clipper until fully dried. 5. Keep the clipper, cord and any attachments away from heated surfaces. 6. Never drop or insert any object into any opening. 7. Do not ...