valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
The clipper has 7 different hair length settings: - 3 mm - 6 mm - 9 mm - 12 mm - 15 mm - 18 mm - 21 mm Start at the setting for maximum hair length (21 mm) to familiarise yourself with the clipper. ENGLISH 7 ENGLISH 4 Make sure that the flat part of the comb attachment is always fully in contact with the scalp to obtain an even cutting result. 5 Pass the clipper slowly over the crown from different directions to achieve an even cutting result. 6 Make overlapping passes over the head to ensure that the clipper catches all the hairs that need to be cut. 7 Comb the hair in the direction of hair growth from time to time so that the clipper can catch the hair more easily. 8 To achieve a good result with curly, sparse or long hair, you can use a comb to guide the hair towards the clipper. 9 We advise you to regularly remove clipped hair from the comb while clipping. Graduation The Philishave hair clipper not only allows you to cut the hair evenly at the same length all over the head, it also enables you to achieve a smooth transition from longer hair on top of the head to shor ter hair on the back and sides of the head. 1 Start clipping at the setting for maximum hair length (i.e. position 21 mm). ENGLISH 2 Then choose a shorter setting and cut the hair on all parts of the head except the top, where you want the hair to be longer. 3 You can repeat this procedure until the hair on every part of the head has the desired length. Precise contouring without comb attachment You can use the clipper without comb attachment to contour the neckline and the area around the ears. Be careful when you are clipping without comb attachment, for the clipper will remove ever y hair it touches. 1 2 3 4 Remove the comb attachment by pulling it off the clipper. Before contouring the hairline round the ears, comb the hair ends over the ear. Bend the person's ear to get it out of the way. Tilt the clipper in such a way that only one edge of the cutting element touches the hair ends. C 5 Only cut the hair ends.The hairline should be close to the ear. C 10 ENGLISH 6 7 8 To contour the nape hairline and the sideburns, turn the clipper and make downward strokes. C Move slowly and smoothly. Just follow the natural hairline. C Cutting over styling comb or fingers This technique can be used to obtain hair lengths over 21 mm. Bear in mind that this technique is difficult to master and should only be applied by experienced users. Remove the comb attachment. C Comb a small section of hair upwards. Lift the hair with a styling comb or hold it between your fingers until only the length that needs to be cut sticks out. C 3 Cut the hair protruding from the comb or fingers. 4 Continue this procedure and comb frequently to remove cut hair and to check for unevenly cut sections. 1 2 Cleaning Clean the appliance every time you have used it. Do not use abrasives, scourers or liquids such as alcohol, petrol or acetone to clean the appliance. 1 Make sure the appliance is switched off and disconnected from the mains before you start cleaning it. C 2 Remove the comb attachment. C 3 Push the middle part of the cutting unit upwards with your thumb until it opens and then pull it off the appliance. Be careful that the cutting unit does not fall to the floor. C 4 Clean the cutting unit and the inside of the appliance with the brush supplied. C 5 Place the lug of the cutting unit into the slot and push the unit back onto the appliance. 6 Make sure you push the cutting unit back until you hear a click. ENGLISH 11 12 ENGLISH Replacement C C A worn or damaged cutting unit should only be replaced with an original Philips cutting unit. 1 2 Push the middle part of the cutting unit upwards with your thumb until it opens and then pull it off the appliance. Place the lug of the cutting unit into the slot and push the cutting unit back until you hear a click. Environment The built-in rechargeable batter y contains substances which may pollute the environment. Remove the rechargeable batter y when you discard the appliance. Do not throw the batter y away with the normal household waste but hand it in at an official collection point. You can also take the appliance to a Philips ser vice centre, which will remove the batter y for you and will dispose of it in an environmentally safe way. 1 Disconnect the appliance from the mains and let the appliance run until the motor stops. ENGLISH 13 2 Open and remove the cutting unit. C 3 Remove the metal clip by means of a screwdriver. C 4 Open the housing. C Inser t a screwdriver into one of the grooves next to the socket for the appliance plug.Turn the screwdriver to separate the two housing halves. 5 Insert a screwdriver into the small slot in the printed circuit board marked with an arrow. Push the screwdriver down until part of the printed circuit board breaks off. C 6 Pull the battery out of the appliance. C Dispose of the batter y and the other components in an environmentally safe way. Do not connect the appliance to the mains a...