valutazioni - 1, GPA: 4
(
)
)
|
Facilità d'uso
The light will stay on as longas the battery is in the charger and the charger is plugged into a working outlet. It WILL NOTflash, go out or change to a different color when the charging cycle is complete. 8. Do not charge power pack in rain or in wet conditions. 9. Use only the batteries and charger supplied with your string trimmer or identical replacement parts. 10.Do not incinerate the batteries. They can explode in a fire. A small leakage of liquid from thebattery cells may occur under extreme usage, charging or temperature conditions. This doesnot indicate a failure. However, if the outer seal is broken and this leakage gets on your skin: a. Wash quickly with soap and water. b. Neutralize with a mild acid such as lemon juice or vinegar. c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutesand seek immediate medical attention. MEDICAL NOTE: The liquid is a 25-35% solution ofpotassium hydroxide. 11.Do not open or mutilate the batteries. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed. 12.Exercise care when handling batteries in order not to short the battery with conducting materials such as rings, bracelets and keys. The battery or conductor may overheat andcause burns. 13.Use only the following type and size battery: PS140 Power Pack - 14.4V. SAVE THESE INSTRUCTIONS ASSEMBLY INSTRUCTIONS • WARNING: The guard must always be on the tool to protect the user and the tool. UNIT ASSEMBLY Layout the unit as shown in figure 4. Align the 3 raised ribs on the lower half with the 3 slots onthe upper half and slide the two halves together until they snap into place. The unit should nowbe rigidly secured. GUARD ASSEMBLY Remove the two screws from the housing shown in figure 5. Align the tab on the guard with therecess at the bottom of the lower half housing as shown in figure 6. Push the guard down ontothe housing and ensure that it is fully seated. Re-insert the two screws through the guard and intothe trimmer housing and tighten as shown in figure 7. NEVER OPERATE THE TOOL WITHOUT THE GUARD PROPERLY IN PLACE. Use of the unit without having installed the guard will cause the motor to overheat, and void the warranty. OPERATING INSTRUCTIONS • CAUTION: ALWAYS WEAR EYE PROTECTION. • CAUTION: Inspect area to be trimmed and remove any wire, cord, or string-like objects whichcould become entangled in the rotating line or spool. Be particularly careful to avoid any wire which might be bent outwardly into the path of the tool, such asbarbs at the base of a chain link fence. • To turn trimmer on, push the lock off button, shown in Figure 1, and squeeze the triggerswitch. To turn the tool off, release the trigger switch. • Angle unit as shown in figure 8. • Slowly swing trimmer side-to-side as shown in Figure 9. CUTTING LINE / LINE FEEDINGYour trimmer only uses .065” (1.65 mm) diameter, ROUND nylon line to cut grass and weedsquickly and easily. During use, the tip of the nylon line will become frayed and worn. Gentlybump the feed head of the trimmer on the ground to release a fresh length of line. Cutting linewill wear faster and require more feeding if the cutting is done along sidewalks or other abrasivesurfaces or heavier weeds are being cut. CLEARING JAMS AND TANGLED LINES From time to time, especially when cutting thick or stalky weeds, the line feeding hub maybecome clogged with sap or other material and the line will become jammed as a result. To clear the jam, follow the steps listed below. 1. Remove battery and turn the unit upside down. 2. Press the release tabs on the line hub cover and remove by pulling it straight off (Figure 10). 3. Lift the spool of nylon line out of the hub and clear any broken line or cutting debris from thespool area. (If you plan to replace the spool or rewind it, this is the place to do so, otherwise, move on.) 4. Unwrap about one foot (30 cm) of line to ensure that it’s undamaged. If it is okay, rewind it and insert the line end through the eyelet in the spool hub as shown in figure 11. Ensure the spring is in place under the spool. Pull the line through the hole to maintain tension whileplacing the spool down into the hub with the arrow up, as shown in figure 11. 5. Press the spool down GENTLY on the spring and rotate it until you feel it drop into place. Take care to keep the line from becoming trapped under the spool. 6. Snap the hub cap back on. Hold the tool in the trimming position, and turn the tool on. In a few seconds or less you’ll hear the nylon line being cut to the proper length; if not, bump thefeed head gently on the ground to initiate a fresh length of line. SPOOL OR LINE REPLACEMENT (Use 0.065” diameter ROUND line only.) 1. Remove battery and turn the unit upside down. 2. Press the release tabs on the line hub cap, as shown in Figure 10 and remove the cap by pullingupward. 3. Remove the spool from the tool and remove and discard all line on spool. 4. Choose either OPTI...
Questo manuale è adatto anche per i modelli :Clippers - CST500 (692.63 kb)