Log:
valutazioni - , GPA: ( )

Istruzioni per l'uso Craftsman, Modello C944.514560

Produttore : Craftsman
File Size : 484.78 kb
File Nome : AYP-MODEL-164843E-PARTS-LIST.pdf

Lingua di insegnamento: en

Il documento viene caricato, si prega di attendere
Il documento viene caricato, si prega di attendere

Facilità d'uso


ing screen. If you operate in a locale ASSEMBLY CARTON CONTENTS Check carton contents against the following list. Model C944.514560 S Powerhead S Lower attachment (with trimmer head installed) S Cupped washer S Large nut for installing blades S Hex wrench S Handlebar S Bracket cover S Bracket cover screws (2) S Metal blade shield S Blade shield screws (4) S 4- --point weed blade S Plastic shield S Wing nut (screwed onto plastic shield) S Shoulder strap with warning S Container of oil Examine parts for damage. Do not use damaged parts. NOTE: If you need assistance or find parts missing or damaged, contact your Sears Service Centre. It is normal for the fuel filter to rattle in the empty fuel tank. Finding fuel or oil residue on muffler is normal due to carburetor adjustments and testing done by the manufacturer. TOOLS REQUIRED S Hex wrench (provided) S Adjustable wrench S Phillips screwdriver ASSEMBLY WARNING: Always stop unit and disconnect spark plug before performing any assembly procedures. WARNING: If received assembled, repeat all steps to ensure your unit is properly assembled and all fasteners are secure. INSTALLING BRUSHCUTTER ATTACHMENT CAUTION: When installing brushcutter attachment, place the unit on a flat surface for stability. 1. Loosen the coupler by turning the knob counterclockwise. Coupler LOOSENTIGHTEN Shipping protector Knob 2. Remove shipping protector from coupler. 3. Remove the shaft cap from the brushcutter attachment (if present). 4. Position locking/release button of attachment into guide recess of coupler. 5. Push the attachment into the coupler until the locking/release button snaps into the primary hole. 6. Before using the unit, tighten the knob securely by turning clockwise. Locking/ GuideRecessCoupler Primary Hole Upper Lower Release Shaft Attachment Button WARNING: Make sure the locking/ release button is locked in the primary hole and the knob is securely tightened before operating the unit. All attachments are designed to be used in the primary hole. 5 For optional attachments, see the AS-NOTE: It may be necessary to relo- SEMBLY section of the applicable at-cate the shoulder strap clamp on the tachment instruction manual. shaft for proper balancing of unit. ATTACHING THE HANDLEBAR TO RELOCATE SHOULDER STRAP CLAMP: DANGER: To avoid serious inju-1. Loosen and remove both clamp ry, the barrier portion of the handlebar must be installed as shown to provide a barrier between operator and the spinning blade. 1. Locate the decal on the handlebar. This decal includes an arrow. Position the handlebar with the mounting bracket at the end of the arrow. 2. Position the bracket cover over the handlebar. Again make sure the handlebar is at the end of the arrow. 3. Insert screws and hand tighten only. Be sure the handlebar is installed correctly; then, tighten each screw securely with the hex wrench. ScrewMountingBracketHandlebarBracketCover ASSEMBLY OF SHOULDER STRAP WARNING: Proper shoulder strap and handlebar adjustments must be made with the engine completely stopped before using unit. 1. Insert your right arm and head through the shoulder strap and allow it to rest on your left shoulder. Make sure the danger sign is on your back and the hook is to the right side of your waist. NOTE: A one-half twist is built in the shoulder strap to allow the strap to rest flat on the shoulder. 2. Adjust the strap, allowing the hook to be about 6 inches below the waist. 3. Fasten the strap hook to the clamp located between the trigger handle and the handlebar clamp base and lift the tool to the operating position. 4. Try on shoulder strap and adjust for fit and balance before starting the engine or beginning a cutting operation.It may be necessary to relocate the shoulder strap clamp on the shaft for proper balancing of unit. screws. 2. Place the upper shoulder strap clamp over the shaft. 3. Position the lower shoulder strap clamp under the shaft and align the upper and lower clamp screw holes. UpperShoulderStrapClamp Lower Shoulder Strap Clamp Screws 4. Insert two screws into the screw holes. 5. Secure shoulder strap clamp by tightening screws with a hex wrench. 30inchesHARNESSADJUSTMENTFORBALANCE4--12inchesaboveground6inchesbelowwaist30inches 6 CONFIGURING YOUR UNIT and retaining washer are positioned You can configure your unit using a cutting head for grass and light weeds, or a weed blade for cutting grass, weeds, and brush up to 1/2 inch (1 cm) in diameter. To assemble your unit, go to the section for the desired configuration and follow the instructions. ASSEMBLY INFORMATION - -- TRIMMER HEAD TRIMMER HEAD NOTE: Remove the blade and metal on the gearbox as shown. WingNutDustCupBracketSlotShieldGearboxRetainingWasher NOTE: Make sure all parts are properly installed as shown in the illustration before installing the trimmer head. 5. Align hole in the dust cup with the hole in the side of the gearbox by rotating the dust cup. 6. Insert a small screwdriver into shield before attaching the plastic...

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie