valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
Pour slowly. See figure 15. 2. Fill the fuel tank with clean, fresh, lead-free, low lead, or regular grade leaded gasoline. DO NOT MIX OIL WITH GASOLINE. 3. Move the engagement handle (depth control) back as far as it will go and place in the last notch. See figure 12. 4. Set the throttle control in "START” position. 5. Pull the choke knob out. NOTE A warm engine may not require choking. 6. Grasp the starter handle and pul! out the cord rapidly. Return it slowly to the engine. If the engine does not start after two pulls, move the throttle control to the "FAST" position. 7. After engine starts, push choke knob in gradually. To stop engine, move throttle control to "STOP" position. Disconnect spark plug wire and ground to prevent accidental starting while equipment is unattended. 9 I A CAUTION Rotating cutting blade may throw objects causing personal injury. Always wear safety glasses or some other suitable eye protection at all times the engine is running. Keep area clear of bystanders and do not operate without guards in place. OPERATING THE EDGER 1. Set the adjustment lever (refer to figure 12 in the second notch at the top to edge vertici lly. See figure 16. FIGURE 16 2. Set the adjustment lever (refer to figure 13) in the first notch at the top for trenching. See figure 17. FIGURE 17 3. To edge along a curb, remove the hairpin clip from the left side of the front axle, slide the left wheel toward the right side of the unit and replace the hairpin clip. See figure 18. Lower the right rear wheel by moving the height adjustment lever toward the engine, pivoting the w leel to the desired depth and releasing the lever. See figure 19. FIGURE 18 Height Adjustment Lever FIGURE 19 4. To operate the unit as a trimmer, move the adjustment lever and rotate the cutting blade 90°. See figure 20. Move the front wheels all the way to the right, as described in the Control section. ▲ CAUTION Do not adjust the blade guard with the engine running. FIGURE 20 LUBRICATION Wheels - The wheels are plastic and require no lubrication. Engine - Refer to engine manual for lubrication instructions. Cutting Head Bearings - The two ball bearings in the cutting head are lubricated and sealed at the factor ' and require no lubrication. Lubricate all other me ing parts with engine oil. Shaft - Lubricate the two bearings and under the compression spring on the shaft with light oil at least once a season. See figure 21. 10 MAINTENANCE AC WARNING \ Disconect the spark plug wire and ground against the engine before performing any adjustment, repairs or maintenance. BLADE REMOVAL Use a wrench on both sides of the blade when removing it for replacement. BELT REMOVAL 1. To remove the V-belt, remove the belt guard v. assembly at the engine pulley. Remove the hex nuts and lock washers. See figure 21. 2. Remove the belt guard at the spindle assembly by removing two hex bolts, lock washers and hex nuts. See figure 22. 3. Remove the old belt, and reassemble with a new belt, part number 754-0142. FIGURE 22 ENGINE OIL Check oil level before starting engine and after every 5 hours of operation. Add oil as necessary to keep level full to point of overflowing. Before removing plug, clean area around plug to prevent dirt from entering oil fill opening. Refer to figure 15. Change oil after firsst 5 hours of operation. Thereafter, change every 25 hours. Change oil while engine is warm. Oil may be drained thru oil drain plug. Crankcase capacity - 1-1/4 pints. Refer to engine manual for complete instructions for care and maintenance of engine. OFF-SEASON STORAGE The following steps should be taken to prepare unit for storage. 1. Clean and lubricate unit thoroughly. 2. Refer to engine manual for correct engine storage instructions. 3. Coat unit's cutting blade with chassis grease to prevent rusting. 4. Store unit in a dry, clean area. ■► NOTE When storing any type of power equipment in an unventilated or metal storage shed, care should be taken to rustproof the equipment. Using a light oil or silicone, coat the equipment, especially springs and bearings. 11 Models 604 and 24604 12 Models 604 and 24604 PARTS LIST FOR MODEL 604 EDGER REF. NO. PART NO. COLOR CODE DESCRIPTION NEW PART REF. NO. PART NO. COLOR CODE DESCRIPTION NEW PART 1 07071 Black Grip 52 15319B Bearing Housing N 2 712-0107 Hex L-Nut 1/4-20 Thd. 53 741-0155 Ball Bearing .62" I.D. 3 714-0115 Cotter Pin 1/8" Dia. 54 710-0258 Hex Bolt 1/4-20 x .62" Lg.* 4‘ 710-0106 Hex Bolt 1/4-20 x 1.25" Lg.* 55 756-0449 3/8" "V'-Pulley 5 710-0380 Hex Bolt 5/16-18 x 1.75" Lg* 56 754-0142 "V'-Belt 6 749-0666 Engagement Handle 57 710-0929 Hex Bolt 5/8-18 x 4.5" Lg* 7 781-0081 Adjustment Bracket 58 710-0258 Hex Bolt 1/4-20 x .625" Lg* 8 732-0369 Compression Spring 1.38" Lg. 59 781-0086 Belt Guard 9 736-0264 Fl.-Wash. .344" I.D. 60 750-0118 Sleeve .90" Lg. 10 712-0158 Hex L-Nut 5/16-18 Thd. 61 712-0267 Hex Nut 5...
Questo manuale è adatto anche per i modelli :Clippers - 249-604-000 (1.46 mb)