valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
scheda madre - GA-K8A480M-9 (6.87 mb)
scheda madre - GA-K8A480M-9 (411.99 kb)
Facilità d'uso
2 (1) Installing SATA hard drive(s) in your system ............................................................................. 2 (2) Configuring SATA controller mode and boot sequence in BIOS Setup .................................... 3 (3) Configuring RAID set in RAID BIOS ............................................................................................. 5 (4) Making a SATA controller driver disk ........................................................................................ 13 (5) Installing SATA controller driver during OS installation ............................................................ 15 Configuring SATA Hard Drive(s) (Controller: ULi M1573) To configure SATA hard drive(s), follow the steps below: (1) Install SATA hard drive(s) in your system. (2) Configure SATA controller mode and boot sequence in BIOS Setup. (3)* Configure RAID set in RAID BIOS. (4) Make a floppy disk containing the SATA controller driver. (5) Install the SATA controller driver during OS installation. Before you begin Please prepare: (a) Two SATA hard drives (to ensure optimal performance, it is recommended that you use two hard drives with identical model and capacity). If you do not want to create RAID with the SATA controller, you may prepare only one hard drive. (b) An empty formatted floppy disk. (c) Windows XP/2000 setup disk. (d) Driver CD for your motherboard. (1) Installing SATA hard drive(s) in your system Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA port(s) on the motherboard. Then connect the power connector from your power supply to the hard drive. "*" Skip this step if you do not want to create RAID array on the SATA controller. SATA Hard Drive Configurations (ULi M1573) -2 (2) Configuring SATA controller mode and boot sequence in BIOS Setup You have to make sure whether the SATA controller is configured correctly in system BIOS Setup and set BIOS boot sequence for the SATA hard drive(s). Step 1: Turn on your computer and press Del to enter BIOS Setup during POST (Power-On Self Test). In the BIOS Setup menu, go to the Integrated Peripherals menu and assure that the OnChip Serial ATA Controller is enabled. If you want to create RAID, set OnChip Serial ATA Controller to Enabled (Enabled by default). Set OnChip Serial ATA Controller to Disabled if you do not want to create RAID. CMOS Setup Utility-Copyright (C) 1984-2005 Award Software Integrated Peripherals Azalia Controller Front Panel Type OnChip Serial ATA Controller Onboard H/W LAN On-Chip Primary IDE On-Chip Secondary IDE On-Chip USB 1.1 Controller USB Keyboard Support USB Mouse Support On-Chip USB 2.0 Controller Onboard Serial Port 1 Onboard Serial Port 2 Onboard Parallel Port Parallel Port Mode [Enabled] [HD Audio] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Disabled] [Disabled] [Enabled] [3F8/IRQ4] [2F8/IRQ3] [378/IRQ7] [SPP] Item Help Menu Level• ........: Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F6: Fail-Safe Defaults F7: Optimized Defaults Figure 1 The BIOS Setup menus described in this section may not show the exact settings for your motherboard. The actual BIOS Setup menu options you will see shall depend on the motherboard you have and the BIOS version. -3 -SATA Hard Drive Configurations (ULi M1573) Step 2: Later, select Hard Disk Boot Priority under the Advanced BIOS Features menu and then choose the model of the SATA hard drive onto which you want to install Microsoft Windows 2000/XP (Figure 2). CMOS Setup Utility-Copyright (C) 1984-2005 Award Software Hard Disk Boot Priority 1. Bootable Add-in Cards 2. SCSI1 ST3120026AS 3. SCSI0 ST3120026AS ....: Move PU/PD/+/-: Change Priority F10: Save ESC: Exit Item Help Menu Level ..• Use <..> or <..> to select a device, then press <+> to move it up, or <-> to move it down the list. Press