valutazioni - 0, GPA: 0 ( )

Produttore : Gigabyte File Size : 7.31 mb File Nome : Lingua di insegnamento:

da questo dispositivo ha anche altre istruzioni :

scheda madre - GA-EP45C-UD3R (8.47 mb)

All Rights Reversed. [ CREATE VOLUME MENU ] Name : Volume0 RAID Level : |RAID0(Stripe) Disks : Select Disks Strip Size : 128KB Capacity : 223.6 GB Create Volume Choose the RAID level: RAID0: Stripes data (performance). RAID1: Mirrors data (redundancy). RAID10: Mirrors data and stripes the mirror. RAID5: Stripes data and parity. [ESC]-Previous Menu [ENTER]-Select Figure 4 Step 4: Under Disks item, select the hard drives to be included in the RAID array. If only two hard drives are installed, they will be automatically assigned to the array. Set the stripe block size (Figure 5) if necessary. The stripe block size can be set from 4 KB to 128 KB. Once you have selected the stripe block size, press . I Intel(R) Matrix Storage Manager option ROM v8.0.0.1039 ICH10R wRAID5 Copyright(C) 2003-08 Intel Corporation. All Rights Reversed. [ CREATE VOLUME MENU ] Name RAID Level Disks Strip Size Capacity Volume0 RAID0(Stripe) Select Disks 223.6 GB Create Volume The following are typical values: RAID0 - 128KB RAID10- 64KB RAID5 - 64KB [Î i]-Change [TAB]-Next [ESC]-Previous Menu [ENTER]-Select Figure 5 [ HELP] [ HELP] GA-EP45C-UD3R/UD3 Motherboard - 84 - Step 5: Enter the array capacity and press . Finally press on the Create Volume item to begin creating the RAID array. When prompted to confirm whether to create this volume, press to confirm or to cancel (Figure 6). Intel(R) Matrix Storage Manager option ROM v8.0.0.1039 ICH10R wRAID5 Copyright(C) 2003-08 Intel Corporation. All Rights Reversed. [ CREATE VOLUME MENU ] Name RAID Level Disks Strip Size Capacity RAID_Volume0 RAID0(Stripe) Select Disks 128KB 223.6 GB WARNING : ALL DATA ON SELECTED DISKS WILL BE LOST. Are you sure you want to create this volume? (Y/N) : Press ENTER to create the specified volume. [Î i]-Change [TAB]-Next [ESC]-Previous Menu [ENTER]-Select Figure 6 When completed, you can see detailed information about the RAID array in the DISK/VOLUME INFORMATION section, including the RAID level, stripe block size, array name, and array capacity, etc. (Figure 7) Intel(R) Matrix Storage Manager option ROM v8.0.0.1039 ICH10R wRAID5 Copyright(C) 2003-08 Intel Corporation. All Rights Reversed. = [ MAIN MENU ] = 2. Delete RAID Volume 3. Reset Disks to Non-RAID 4. Exit = [ DISK/VOLUME INFORMATION ] = RAID Volumes : ID Name 0 Volume0 Physical Disks : Port Drive Model 0 ST3120026AS 1 ST3120026AS [Î i]-Select Level Strip RAID0(Stripe) 128KB Serial # 3JT354CP 3JT329JX Size Status Bootable 223.6GB Normal Yes Size Type/Status(Vol ID) 111.8GB Member Disk(0) 111.8GB Member Disk(0) [ENTER]-Select Menu Figure 7 To exit the ICH10R RAID BIOS utility, press or select Exit in MAIN MENU. Now, you may proceed to create the SATA RAID/AHCI driver diskette and the installation of the SATA RAID/ACHI driver and operating system. - 85 - Appendix Delete RAID Volume To delete a RAID array, select Delete RAID Volume in MAIN MENU and press . In the DELETE VOLUME MENU section, use the up or down arrow key to select the array to be deleted and press . When prompted to confirm your selection (Figure 8), press to confirm or to abort. Figure 8 GA-EP45C-UD3R/UD3 Motherboard - 86 - 5-1-2 Configuring GIGABYTE SATA2 SATA Controller A. Installing SATA hard drive(s) in your computer Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA port on the motherboard. If there is more than one SATA controller on your motherboard, refer to "Chapter 1," Hardware Installation," to identify the SATA controller for the SATA port. (For example, on this motherboard, the GSATA2_0 and GSATA2_1 ports are supported by GIGABYTE SATA2.) Then connect the power connector from your power supply to the hard drive. B. Configuring SATA controller mode and device boot order in BIOS Setup Make sure to configure the SATA controller mode correctly in system BIOS Setup and set the device boot order. Step 1: Turn on your computer and press to enter BIOS Setup during the POST. In BIOS Setup, go to Integrated Peripherals, ensure that Onboard SATA/IDE Device is enabled. Then set Onboard SATA/IDE Ctrl Mode to RAID/IDE (Figure 1). If you do not want to create RAID, set this item to IDE or AHCI, depending on your need. Figure 1 Step 2: Save changes and exit BIOS Setup. © Only for GA-EP45C-UD3R. Only for GA-EP45C-UD3. The BIOS Setup menus described in this section may differ from the exact settings for your NOTE motherboard. The actual BIOS Setup menu options you will see shall depend on the motherboard you have and the BIOS version. - 87 - Appendix C. Configuring a RAID array in RAID BIOS Enter the RAID BIOS setup utility to configure a RAID array. Skip this step and proceed to the installation of Windows operating system for a non-RAID configuration. After the POST memory test begins and before the operating system boot begins, l...

Scarica la tua

Per scaricare, digitare 2 cifre :