valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
One IDE connector can connect to one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the other as Slave (for information on settings, please refer to the instructions located on the IDE device). IDE2 IDE1 1 39 2 40 5) FDD (FDD Connector) The FDD connector is used to connect the FDD cable while the other end of the cable connects to the FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB. Please connect the red power connector wire to the pin1 position. 33 34 1 2 7) SATA0 / SATA1 (Serial ATA Connector) Serial ATA can provide 150MB/s transfer rate. Please refer to the BIOS setting for the Serial ATA and install the proper driver in order to work properly. Pin No. Definition 1 GND 2 TXP 3 TXN 4 GND 5 RXN 6 RXP 7 GND 7 1 SATA1 7 1 SATA0 For more detailed Serial ATA RAID setup information, please visit our website at http:\\- 15 - Hardware Installation Process English 8) PWR_LED PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode. 9) F_PANEL (2 x 10 pins Connector) Please connect the power LED, PC speaker, reset switch and power switch etc. of your chassis front panel to the F_PANEL connector according to the pin assignment below. MSG (Message LED/ Power/ Sleep LED) Pin 1: LED anode(+) Pin 2: LED cathode(-) PW (Power Switch) Open: Normal Operation Close: Power On/Off SPK (Speaker Connector) Pin 1: VCC(+) Pin 2- Pin 3: NC Pin 4: Data(-) HD (IDE Hard Disk Active LED) Pin 1: LED anode(+) Pin 2: LED cathode(-) RES (Reset Switch) Open: Normal Operation Close: Reset Hardware System NC NC 1 Pin No. Definition 1 MPD+ 2 MPD- 3 MPD- 1 2 19 20 HDHD+ RES+ RESNC IDE Hard Disk Active LED Reset Switch SPEAKMSGMSG+ PWPW+ Message LED/Power/ Sleep LED Speaker Connector SPEAK+ Power Switch 8S648FXP-RZ Series Motherboard - 16 - English 10) F_AUDIO (Front Audio Connector) If you want to use Front Audio connector, you must remove 5-6, 9-10 Jumper. In order to utilize the front audio header, your chassis must have front audio connector. Also please make sure the pin assigment on the cable is the same as the pin assigment on the MB header. To find out if the chassis you are buying support front audio connector, please contact your dealer. Please note, you can have the alternative of using front audio connector or of using rear audio connector to play sound. 10 2 1 9 Pin No. Definition 1 MIC 2 GND 3 MIC_BIAS 4 Power 5 Front Audio (R) 6 Rear Audio (R) 7 Reserved 8 No Pin 9 Front Audio (L) 10 Rear Audio (L) 1 2 6 5 11) SPDIF_IO (SPDIF In/Out Connector) The SPDIF output is capable of providing digital audio to external speakers or compressed AC3 data to an external Dolby Digital Decoder. Use this feature only when your stereo system has digital input function. Be careful with the polarity of the SPDIF_IO connector. Check the pin assignment carefully while you connect the SPDIF cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional SPDIF cable, please contact your local dealer. Pin No. Definition 1 VCC 2 No Pin 3 SPDIF 4 SPDIFI 5 GND 6 GND - 17 - Hardware Installation Process English 12) SUR_CEN (Surround Center Connector) Please contact your nearest dealer for optional SUR_CEN cable. 1 6 5 2 13) CD_IN (CD In Connector) Connect CD-ROM or DVD-ROM audio out to the CD_IN connector 1 Pin No. Definition 1 CD-L 2 GND 3 GND 4 CD-R Pin No. Definition 1 SUR OUTL 2 SUR OUTR 3 GND 4 No Pin 5 CENTER_OUT 6 BASS_OUT 14) F_USB1 / F_USB2 (Front USB Connector) Be careful with the polarity of the front USB connector. Check the pin assignment carefully while you connect the front USB cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional front USB cable, please contact your local dealer. 2 10 1 9 Pin No. Definition 1 Power 2 Power 3 USB DX- 4 USB Dy- 5 USB DX+ 6 USB Dy+ 7 GND 8 GND 9 No Pin 10 NC 8S648FXP-RZ Series Motherboard - 18 - English 16) CLR_CMOS (Clear CMOS) You may clear the CMOS data to its default values by this jumper. To clear CMOS, temporarily short 1-2 pin. Default doesn't include the "Shunter" to prevent from improper use this jumper. 1 1 Open: Normal Short: Clear CMOS 17) BAT (BATTERY) CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. If you want to erase CMOS... 1. Turn OFF the computer and unplug the power cord. 2. Remove the battery, wait for 30 second. 3. Re-install the battery. 4. Plug the power cord and turn ON the computer. 15) IR Be careful with the polarity of the IR connector while you connect the IR. Please contact your nearest deale...