The actual BIOS Setup menu options you will see shall depend on the motherboard you have and the BIOS version. GA-8I945GMMFY-RH Motherboard - 64 Step 2: Later, select Hard Disk Boot Priority under the Advanced BIOS Features menu. In the Hard Disk Boot Priority submenu, select the model of the SATA hard drive onto which you intent to install Microsoft Windows 2000/XP (Figure 2). English Figure 2 CMOS Setup Utility-Copyright (C) 1984-2005 Award Software Hard Disk Boot Priority 1. SCSI-0 : Intel Volume0 2. Bootable Add-in Cards ....: Move PU/PD/+/-: Change Priority F10: Save ESC: Exit Item Help Menu Level .... Use <..> or <..> to select a device, then press <+> to move it up, or <-> to move it down the list. Press to exit this menu. Step 3: Set First Boot Device under the Advanced BIOS Features menu to CD-ROM to boot from CD-ROM after system restarts (Figure 3). CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Advanced BIOS Features ..Hard Disk Boot Priority [Press Enter] First Boot Device [CD-ROM] Second Boot Device [Hard Disk] Third Boot Device [CDROM] Password Check [Setup] Limit CPUID Max. to 3 [Disabled] No-Execute Memory Protect (Note) [Enabled] CPU Enhanced Halt (C1E) (Note) [Enabled] CPU Thermal Monitor 2(TM2) (Note) [Enabled] CPU EIST Function (Note) [Enabled] Virtualization Technology [Enabled] On-Chip Frame Buffer Size [8MB] ........: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults Item Help Menu Level.. Select Hard Disk Boot Device Priority Step 4: Save and exit BIOS Setup. Figure 3 - 65 Appendix English (3) Configuring RAID set in RAID BIOS Enter the RAID BIOS setup utility to configure a RAID array. Skip this step and proceed to Section 4 if you do not want to create RAID. Step 1: After the POST memory test begins and before the operating system boot begins, look for a message which says "Press to enter Configuration utility" (Figure 4). Press CTRL+ I to enter the RAID BIOS setup utility. Intel(R) Matrix Storage Manager option ROM v5.7.0.1007 ICH7MR Copyright(C) 2003-05 Intel Corporation. All Rights Reversed. RAID Volumes : None Defined. Physical Disks : Port Driver Model Serial # Size Type/Status(Vol ID) 0 ST3120026AS 3JT354CP 111.8GB Non-RAID Disk 1 ST3120026AS 3JT329JX 111.8GB Non-RAID Disk Press to enter Configuration Utility Figure 4 Step 2: After you press CTRL+ I, the Create RAID Volume screen will appear (Figure 5). Create RAID Volume: If you want to create RAID array, select Create RAID Volume in Main Menu and press ENTER. Intel(R) Matrix Storage Manager option ROM v5.7.0.1007 ICH7MR Copyright(C) 2003-05 Intel Corporation. All Rights Reversed. [ MAIN MENU ] 1. Create RAID Volume 2. Delete RAID Volume 3. Reset Disks to Non-RAID 4. Exit RAID Volumes : None Defined. Physical Disks : Port Driver Model 0 ST3120026AS 2 ST3120026AS Serial # Size 3JT329JX 111.8GB 3JT354CP 111.8GB [ DISK/VOLUME INFORMATION ] Type/Status(Vol ID) Non-RAID Disk Non-RAID Disk [....]-Select [ESC]-Exit [ENTER]-Select Menu Figure 5 GA-8I945GMMFY-RH Motherboard - 66 English Step 3: After entering the Create Volume Menu screen, name the disk array with 1~16 letters (letters cannot be special characters) under the Name item. When finished, press ENTER to select a RAID level (Figure 6). There are four RAID levels: RAID0, RAID1. Select a RAID level and press ENTER. Intel(R) Matrix Storage Manager option ROM v5.7.0.1007 ICH7MR Copyright(C) 2003-04 Intel Corporation. All Rights Reversed. [ HELP ] [ CREATE VOLUME MENU ] Name : RAID_Volume0 RAID Level : RAID0(Stripe) Disks : Select Disks Strip Size : 128KB Capacity : 223.6 GB Create Volume RAID0RAID1Choose the RAID level best suited to your usage model. Data striped across multiple physical drives for performance. Data mirrored across multiple physical drives for redundancy. [....]-Change [TAB]-Next [ESC]-Previous Menu [ENTER]-Select Figure 6 Step 4: Set the stripe block size (Figure 7). The KB is the standard unit of stripe block size. The stripe block size can be set from 4KB to 128KB. After the setting, press ENTER to set array capacity. Intel(R) Matrix Storage Manager option ROM v5.7.0.1007 ICH7MR Copyright(C) 2003-05 Intel Corporation. All Rights Reversed. [ CREATE VOLUME MENU ] Name : RAID_Volume0 RAID Level : RAID0(Stripe) Disks : Select Disks Strip Size : 128KB Capacity : 223.6 GB Create Volume [ HELP ] The following are typical values: RAID 0 -128KB [....]-Change [TAB]-Next [ESC]-Previous Menu [ENTER]-Select Figure 7 -67 -Appendix English Step 5: After setting all the items above, select Create Volume and press ENTER (Figure 8) to begin the creation of the RAID array. Intel(R) Matrix Storage Manager option ROM v5.7.0.1007 ICH7MR Copyright(C) 2003-05 Intel Corporation. All Rights Reversed. [ CREATE VOLUME MENU ] Name : RAID_Volume0 RAID Level : RAID0(Stripe) Disks : Select Disks Strip Size : 128KB Capacity : 223.6 GB Create Volume Enter the volume...
