valutazioni - 3, GPA: 3.3 ( )

Produttore : Daewoo File Size : 686.67 kb File Nome : Lingua di insegnamento:

1) KOR-631G0A/631H0A/631H9A/631G9A REF NO. PART CODE PART NAME DESCRIPTION Q’TY REMARK A01 3512203870 FRAME DOOR ABS SG-175, SG-0760B 1 A02 3517006180 BARRIER-SCREEN*0 SAN T1.5 1 A03 3515304610 SUPPORTER BARR-S*0 PP 1 A04 3515204100 STOPPER SINGE *T AS KOR-63150S 1 A05 3511705500 DOOR WELD AS KOR-61150S 1 A06 3517002800 BARRIER-SCREEN *I POLYESTER T0.1 1 A07 3512300200 GASKET DOOR PP 1 A08 3513100740 HOOK POM (LG.›.— ) 1 A09 3515101300 SPRING HOOK PW1 1 2) KOR-861G0A/861H0A REF NO. PART CODE PART NAME DESCRIPTION Q’TY REMARK A01 3512204110 FRAME DOOR ABS XR-401, H-2938 1 A02 3517003150 BARRIER-SCREEN*0 ACRYL 1 A03 3515304410 SUPPORTER BARR-S*0 PP 1 A04 3515204100 STOPPER SINGE *T AS KOR-63150S 1 A05 3511705620 DOOR WELD AS KOR-81250S 1 A06 3517002900 BARRIER-SCREEN *I POLYESTER T0.1 1 A07 3512300400 GASKET DOOR PP 1 A08 3513100700 HOOK POM 1 A09 3515101300 SPRING HOOK PW1 1 12 (1) Remove the gasket door from door weld as. (2) Remove the barrier screen inner from door weld as. (3) Remove the door frame from door weld as. (4) Remove the stopper hinge top from door weld as. (5) Remove the spring and the hook. (6) Remove the supporter barrier screen outer from door frame. (7) Remove the barrier screen outer from door frame. (8) Reverse the above steps for reassembly. 4. Method to reduce the gap between the door seal and the oven front surface. (1) To reduce gap located on part ‘A’ Loosen a screws on stopper hinge top, and then push the door to contact the door seal to oven front surface. Tighten two screws. (2) To reduce gap located on part ‘B’ Loosen two screws on stopper hinge under, and then push the door to contact the door seal to oven front surface. Tighten two screws. NOTE : A small gap may be acceptable if the microwave leakage does not exceed 4mW/cm2. 13 4 Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service information Center(5. To remove control panel parts. 1) KOR-631G0A/631H0A/631H9A/631G9A REF NO. PART CODE PART NAME DESCRIPTION Q’TY REMARK B01 3518521000 SWITCH MEMBRANE KOR-631G0A/9A 1 3518521010 SWITCH MEMBRANE KOR-631H0A/9A 1 B02 3516719500 CONTROL PANEL ABS AF-345 HFA-700HT 1 3516719530 CONTROL PANEL VT-0826, AF-348 1 KOR-631G/H9A B03 3514320660 PCB AS KOR-631H9A 1 B04 7122401211 SCREW TAPPING T2S TRS 4X12 MFZN 3 B05 3513702710 LEVER DOOR OPEN ABS XR-401 H-2938 1 B06 441G430171 SPRING BUTTON SWP DIA0.7 1 B07 3516906900 BUTTON DOOR OPEN ABS AF-345 HFA-700HT 1 2) KOR-861G0A/861H0A REF NO. PART CODE PART NAME DESCRIPTION Q’TY REMARK B01 3518521500 SWITCH MEMBRANE KOR-861G0A 1 3518521510 SWITCH MEMBRANE KOR-861H0A 1 B02 3516720400 CONTROL PANEL ABS AF-345, HFA-700HT 1 B03 3514320910 PCB MAIN AS KOR-861G0A 1 B04 7122401211 SCREW TAPPING T2S TRS 4X12 MFZN 1 B05 3513702710 LEVER DOOR OPEN ABS XR-401 H-2938 1 B06 441G430171 SPRING BUTTON SWP DIA0.7 1 B07 3516906900 BUTTON DOOR OPEN ABS XR-401 H-2938 1 14 15 6. To remove high voltage capacitor. 1) Remove a screw which secure the grounding ring terminal of the H.V. diode and the capacitor holder. 2) Remove the H.V. diode from the capacitor holder. 3) Reverse the above steps for reassembly. High voltage circuit wiring 7. To remove magnetron. 1) Remove a screw which secure the magnetron. 2) Remove the magnetron. 3) Reverse the above steps for reassembly. NOTE : Never install the magnetron without the metallic gasket plate which is packed with each magnetron to prevent microwave leakage. Whenever repair work is carried out on magnetron, check the microwave leakage. It shall not exceed 4mW/cm2 for a fully assembled oven with door normally closed. 1) Remove the screw which secure the control panel, push up two snap fits and draw forward the control panel assembly. 2) Remove the door open lever from the control panel. 3) Remove four screws which secure the PCB assembly to control panel. 4) Disconnect membrane tail from the connector of the PCB assembly. 5) Detach membrane from the control panel. 6) Remove door open button and button spring from the control panel. 7) Reverse the above steps for reassembly. 16 8. To remove wind guide assembly. 1) Remove a screw which secure the wind guide assembly. 2) Draw forward the wind guide assembly. 3) Pull the fan from the motor shaft. 4) Remove two screws which secure the motor shaded pole. 5) Remove the motor shaded pole. 6) Reverse the above steps for reassembly. 9. To remove H.V.transformer. 1) Remove four screws holding the H.V.transformer. 2) Remove the H.V.transformer. 3) Reverse the above steps for reassembly. INTERLOCK MECHANISM AND ADJUSTMENT The door lock mechanism is a device which has been specially designed to completely eliminate microwave radiation when the door is opened during operation, and thus to perfectly prevent the danger resulting from the leakage of microwave. (1) Primary interlock switch When the door is cl...

Scarica la tua

Per scaricare, digitare 2 cifre :