valutazioni - 3, GPA: 4.3 ( )

Produttore : Broan File Size : 2.14 mb File Nome : Lingua di insegnamento:

Remove damper/duct connector from inside the hood. FOR DUCTED INSTALLATIONS - Skip to Step 12. |~8~| NON-DUCTED INSTALLATION ONLY: From parts bag: Attach Non-Duct Diverter to Air Box with 2 Screws and 2 Washers. |~9~| NON-DUCTED INSTALLATION ONLY: Remove 2 Screws holding Non-Duct Plate to Non-Duct Plenum and remove plate. [ÏÏÏ] NON-DUCTED INSTALLATION ONLY: Insert short end of Non-Duct Plate into Non-Duct Plenum Slot. Attach with 2 Screws removed in Step 9. [ïï~| NON-DUCTED INSTALLATION ONLY: Purchase a set of (2) non-ducted filters for 30” wide hoods (Model BPPF30) & 36” wide hoods (Model BPPF36) or a set of (3) non-ducted filters for 42” wide hoods (Model BPPF42) from your local distributor or retailer. Attach the non-ducted filters to the aluminum mesh filters following instructions packed with the non-ducted filters. FOR NON-DUCTED INSTALLATIONS - Skip to “INSTALL THE HOOD" BROAN MDLS [T2~ DUCTED INSTALLATION ONLY: Remove 3%” x 10 vertical, 3%” x 10” horizontal, or 7-inch round knockout plate(s) as appropriate for your ducting method. R3J DUCTED INSTALLATION ONLY: Attach 314” x 10” Damper/Duct Connector (if using 3%” x 10” duct) or 7” Round Duct Plate (if using 7-inch round duct) over the knockout opening. Notes: To accomodate off-center ductwork, the 3%” x 10” damper/duct connector can be installed up to /2” on either side of the hood center and the 7” round duct plate can be installed up to /” on either side of the hood center. Install the 3%” x 10” Damper/Duct Connector with the Damper Flap Pivot nearest the Top/Back Edge of Hood. QP230BC • QP230BL • QP230SS • QP230WW QP236BC • QP236BL • QP236SS • QP236WW QP242BC • QP242BL • QP242SS • QP242WW Page 5 INSTALL THE HOOD_ A WARNING To reduce the risk of electrical shock, switch power off at service panel. Lock or tag service panel to prevent power from being switched on accidentally. 14 | Remove Electrical Wiring Box Cover from inside of hood and appropriate Electrical Power Cable Knockout from top or back of hood. p5| Run House Power Cable between service panel and hood location. Attach power cable to hood using appropriate clamp. [i6~| Hang hood from (4) mounting screws driven part-way into cabinet locations (shown in illustrations under “PREPARE HOOD LOCATION”). Mounting screws are included in parts bag. Slide hood back towards wall until mounting screw heads are engaged in narrow end of keyhole slots in top of hood. Tighten screws securely. Add 5th mounting screw in center hole in hood and tighten securely. |r7] DUCTED INSTALLATION ONLY: Connect ductwork to hood and use duct tape to make joints secure and air-tight. Make sure the damper / duct connector enters the ductwork and that the damper opens and closes freely. BR6ÄN MODELS QP230BC • QP230BL • QP230SS • QP230WW QP236BC • QP236BL • QP236SS • QP236WW QP242BC • QP242BL • QP242SS • QP242WW CONNECT THE WIRING 181 Connect House Power Cable to range hood wiring -^ BLACK to BLACK, WHITE to WHITE, and GREE...

Scarica la tua

Per scaricare, digitare 2 cifre :