valutazioni - 3, GPA: 4.7
(
)
)
|
Facilità d'uso
. . Each preset key has four time settings. The indicator above the number 1, 2, 3, or 4 and the P1 or P2 indicator light identify which preset time is being displayed. The chart below shows the default settings; the next page shows how to revise these preset times. The Dial Timer KNOB can be used to adjust the mixing time if the knob is turned prior to pressing START. Beginning from the Idle display [ – – : – – ], press P1 or P2 to display the #1 preset mixing time. (Pressing P1 or P2 again will display the next preset time, etc.) 01:00 -- - - -P1 - * The Dial Timer KNOB can adjust the time. P2 1 2 3 4 START and STOP buttons control mixing operation. Indicators above P1 and 1 indicate the first preset time Press START to begin mixing: The timer will countdown from the set time to [ 00 : 00 ]. contained in P1. If STOP is pressed, both mixing and timer countdown will be interrupted. After pressing STOP . . . Press START to resume both mixing and timer countdown; or, press CLEAR to return to the Idle display. When the mixer is stopped, you may perform any appropriate task, such as the following: Add ingredients, change speed, reset the timer, continue mixing, or unload. When the timer reaches [ 00 : 00 ] the mixer stops; a beep tone sounds for two seconds; and the next preset mixing time displays. When the last preset time reaches [ 00 : 00 ], the P1 or P2 indicator goes off; and the Idle display [ – – : – – ] returns. Repeat from * to complete four preset times. The timer reverts to the Factory Programmed Preset Times after any power interruption: Factory Programmed Preset Times Preset Key Indicator 1 2 3 4 P1 01:00 02:00 10:00 00:00 P2 02:00 01:00 05:00 03:00 – 7 – PROGRAMMABLE TIMER CONTROLLER (when equipped) continued To Revise the Preset Mixing Times contained in P1 or P2 . . . Each preset key has four preset time settings. The indicator above the number 1, 2, 3, or 4 and the P1 or P2 indicator light identify which preset time is being displayed. Beginning from the Idle display [ – – : – – ], press P1 or P2 to display the #1 preset mixing time. ( Pressing P1 or P2 again will display the next preset time, etc.) 01:00 -- - - -P1 - + Turn the KNOB to change the time for the indicated preset. P2 1 2 3 4 • Press SAVE to retain the revised time and move to the next preset time. Indicators above P1 and 1 indicate the Repeat from + for each preset time (1, 2, 3, and 4 contained in P1 or P2). first preset time contained in P1. Pressing CLEAR will retain the saved times and return to the Idle display [ – – : – – ]. The timer reverts to the Factory Programmed Preset Times after any power interruption: Factory Programmed Preset Times Preset Key Indicator 1 2 3 4 P1 01:00 02:00 10:00 00:00 P2 02:00 01:00 05:00 03:00 – 8 – CHANGING SPEEDS The GEAR SHIFT LEVER is used to change speeds. Always stop the mixer before changing speeds. To change speeds, push the STOP button, move the gear shift lever to the desired speed, and restart the mixer by pushing the START button. NOTE: If you do not stop the mixer to change speeds, it will automatically shut itself off and you will have to restart it after changing speeds. Mixer Speeds Speed 1 (Low) — This speed is for heavy mixtures such as bread dough, heavy batters, and potatoes. Speed 2 (Medium) — This speed is for light dough which must rise quickly, cake batters, mashing potatoes, and some whipping operations. Speed 3 (High) — This is a fast speed for light work, such as whipping cream, beating eggs, and mixing thin batters. BOWL LIFT D330 models equipped with a Lift Lever raise the bowl by rotating the Lift Lever downward; and lower the bowl by rotating the Lift Lever upward. MIXING This section explains operation of the mixer and how to install bowls, agitators, and attachments. A separate Use and Applications Handbookis provided with the mixer which contains information on mixing procedures and outlines specific uses for agitators, attachments, and accessories. Bowl New mixer bowls and agitators (beaters, whips, and dough arms) should be thoroughly washed with hot water and a mild soap solution, rinsed with either a mild soda or vinegar solution, and thoroughly rinsed with clear water BEFORE being used. This cleaning procedure should also be followed for bowls and agitators before whipping egg whites or whole eggs. The bowl must be installed before the agitator. To install the bowl, fully lower the bowl support. Position the bowl so the alignment bracket on the back of the bowl is in the bowl retainer on the bowl support and the alignment pins on the front of the bowl support fit in the holes in the bowl. Lock the bowl in place by rotating the bowl clamps over the ears of the bowl. Agitator To install an agitator, the bowl must be installed and fully lowered. Place the agitator in the bowl, push it up on the agitator shaft, and turn it clockwise to seat the shaft pin in the slot of the agitator shank. To Raise the Bowl While Mixing To raise the bowl while the agitator is m...