|
Facilità d'uso
1. In a well ventilated outdoor area add fresh, high quality, unleaded gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. Refer to Engine Owners Manual for correct procedure. 2. Check engine oil level. See Engine Owners Manual for correct procedure. NOTE: There will be a slight amount of oil in the engine from factory testing. 3. Verify the filter screen is in water inlet of pump. NOTE: Cone side faces out. Filter Screen 4. Connect water source to pump inlet. NOTE: Water source must provide a minimum of 5 gallons per minute at 20 PSI. 5. Connect high pressure hose to pump outlet. High Pressure HoseWater Source 6. If applying a chemical or cleaning solution, see How To Apply Chemicals/Cleaning Solvents instructions in this section. 7. Turn water source on. NOTE: Failure to do so could cause damage to the pump. Owners Manual for correct procedure. NOTE: When engine rope is pulled, pressure starts building in the gun. If the engine does not start after two pulls, pull the gun trigger to relieve this pressure. 9. Depress trigger on gun to start water flow. NOTE: Stand on a stable surface and grip gun/spray wand firmly with both hands. Expect the gun to kick when triggered. 10. Release trigger to stop water flow. 11. Adjust spray for the task being performed by changing quick connect nozzle. See How To Use Spray Wand instructions in this section. SHUTTING DOWN 1. After each use, if you have applied chemicals, place chemical hose into container of clean water and draw clean water through chemical injection system to rinse system thoroughly. NOTE: Failure to do so could cause damage to the pump. 2. Turn engine off. See Engine Owner’s Manual. NOTE: NEVER turn the water off with the engine running. 3. Turn water source off. 4. Pull trigger on spray gun to relieve any water pressure in hose or spray gun. 5. See Storage section in this manual for proper storage procedures. 11-ENG A12495 MAINTENANCE When performing maintenance, you may be exposed to hot surfaces, water pressure, or moving parts that can cause serious injury or death! Before performing any maintenance or repair, disconnect spark plug wire, let engine cool and release all water pressure. The engine contains flammable fuel. DO NOT smoke or work near open flames while performing maintenance. To ensure efficient operation and longer life of your pressure washer, a routine maintenance schedule should be prepared and followed. If the pressure washer is used in unusual conditions, such as high- temperatures or dusty conditions, more frequent maintenance checks will be required. ENGINE Consult the Engine Owners Manual for the manufacturer's recommendations for any and all maintenance. Consult the Engine Owners Manual for the manufacturer's recommendations for any and all maintenance. NOTE: The frame is equipped with an oil drain hole to help make changing the engine oil easier. PUMP NOTE: The pump was filled with oil at the factory. 1. Change pump oil after the first ten (10) hours of operation and every fifty (50) hours thereafter. To Check Oil: 1. Remove dipstick/oil plug from pump and wipe clean. 2. Insert dipstick/oil plug fully into pump, then remove it. Dipstick/oil plugOil Drain Plug 3. Oil level is correct when oil covers the lower 1/2 inch of end of dipstick/oil plug. How To Change Pump Oil 1. Loosen dipstick/oil plug. 2. Place a container under the oil drain plug. 3. Remove oil drain plug. 4. After oil is drained replace oil drain plug. Tighten securely. 5. Remove dipstick/oil plug and fill with 18.54 oz (548.3 ml) of 30W non detergent oil. 6. Replace dipstick/oil plug and tighten securely. A12495 12-ENG NOZZLE CLEANING If the nozzle becomes clogged with foreign materials, such as dirt, excessive pressure may develop. If the nozzle becomes partially clogged or restricted, the pump pressure will pulsate. Clean the nozzle immediately using the nozzle kit supplied and the following instructions: 1. Shut off the pressure washer and turn off the water supply. 2. Pull trigger on gun handle to relieve any water pressure. 3. Disconnect the spray wand from the gun. 4. Remove the high-pressure nozzle from the spray wand. Remove any obstructions with the nozzle cleaning tool provided and backflush with clean water. 5. Direct water supply into spray wand to backflush loosened particles for 30 seconds. 6. Reassemble the nozzle to the wand. 7. Reconnect spray wand to gun and turn on water supply. 8. Start pressure washer and place spray wand into high pressure setting to test. HOW TO CLEAN THE WATER INLET FILTER This screen filter should be checked periodically and cleaned if necessary. 1. Remove filter by grasping end and removing it from water inlet of pump as shown. Filter Screen 2. Clean filter by flushing it with water on both sides. 3. Re-insert filter into water inlet of pump. NOTE: Cone side faces out. NOTE: Do not operate pressure washer without filter properly installed. HOW TO REMOVE THE ...
Questo manuale è adatto anche per i modelli :apparecchiature di lavaggio - Pressure Wave PWH3635 (2.03 mb)