valutazioni - 4, GPA: 3.5
(
)
)
|
Facilità d'uso
Accessory Tray — Provides convenient storage for standard and optional accessories, such as brushes, turbo wands, etc. Air Filter — Protects engine by filtering dust and debris out of intake air. Automatic Cool Down System — Cycles water through pump when water reaches 125°-155°F.Warm water will discharge from pump onto ground.This system prevents internal pump damage. Chemical Injection Siphon/Filter — Use to siphon detergent or other pressure washer chemicals into the low pressure stream. Data Tag (not shown, near rear of base plate) – Provides model and serial number of pressure washer. Please have these readily available if calling for assistance. Fuel Tank — Fill tank with regular unleaded fuel.Always leave room for fuel expansion. High Pressure Hose — Connect one end to water pump and the other end to spray gun. High Pressure Outlet — Connection for high pressure hose. Nozzle Extension with Quick Connect — Allows you to switch between four different nozzles. Oil Fill/Dipstick — Check and fill with oil here. Primer Bulb — Prepares a cold engine for starting. Pump — Develops high pressure. Recoil Starter — Used for starting the engine manually. Spray Gun — Controls the application of water onto cleaning surface with trigger device. Includes trigger lock. ProjectPro™ Nozzles — Detergent, Max, General, and Delicate nozzles: for various pressure cleaning applications. Throttle Lever — Sets engine in starting mode for recoil starter and stops a running engine. Turbo Nozzle — Rotates a high pressure stream in a rapid circular pattern. Water Inlet — Connection for garden hose. Air Filter Primer Bulb Fuel Tank Pump equipped with Automatic Cool Down System Recoil Starter High Pressure Outlet & Water Inlet Chemical Injection Siphon/Filter Spray Gun High Pressure Hose Nozzle Extension with Quick Connect Oil Fill/Dipstick Throttle Lever ProjectPro™ Nozzles Turbo Nozzle Accessory Tray Features and Controls 2 Section Section 3 Assembly ASSEMBLY IMPORTANT: Read entire owner’s manual before you attempt to assemble or operate your new pressure washer. Remove Pressure Washer From Carton 1. Remove the parts bag, accessories, and inserts included with pressure washer. 2. Slice two corners at the end of carton from top to bottom so the panel can be folded down flat. 3. Remove pressure washer from carton. Carton Contents Items in the carton include: • Main Unit • Handle • High Pressure Hose • Spray Gun • Nozzle Extension with Quick Connect Fitting • Plastic Accessory Tray • Safety Goggles • Oil Bottle • Turbo Nozzle with Quick Connect • Parts Bag (which includes the following): • Owner’s Manual • Engine Manual • Owner’s Registration Card • Bag containing 4 multi–colored ProjectPro™ Nozzles • Handle/Tray Fastening Hardware Kit (which includes): • Carriage Bolts (2) • Plastic Knobs (2) • Tree Clips (4) PREPARING PRESSURE WASHER FOR USE If you have any problems with the assembly of your pressure washer or if parts are missing or damaged, call the pressure washer helpline at 1-800-743-4115. If calling for assistance, please have the model, revision, and serial number from the data tag available. To prepare your pressure washer for operation, you will need to perform these tasks: 1. Fill out and send in registration card. 2. Attach handle to main unit, then attach accessory tray to handle. 3. Add oil to engine crankcase. 4. Add fuel to fuel tank. 5. Connect high pressure hose to spray gun and pump. 6. Connect water supply to pump. 7. Attach nozzle extension to spray gun. 8. Select/attach quick connect ProjectPro™ nozzle to nozzle extension. Attach Handle and Accessory Tray 1. Place handle onto handle supports connected to main unit. Make sure holes in handle align with holes on handle supports (Figure 1). Align Holes Handle Handle Supports Figure 1 — Attach Handle to Base NOTE: It may be necessary to move the handle supports from side to side in order to align the handle so it will slide over the handle supports. 6 Section 3: Assembly 2. Insert carriage bolts through holes from outside of unit and attach a plastic knob from inside of unit (Figure 2). Tighten by hand. Figure 2 — Secure Handle 3. Place accessory tray over holes on handle (viewing from front of unit). Push the tree clips into the holes until they sit flat against the accessory tray (Figure 3). Figure 3 — Attach Accessory Tray to Handle 4. Insert multi–colored ProjectPro™ nozzles and other supplied accessories in spaces provided in accessory tray. See “How to Use Accessory Tray”. Add Engine Oil and Fuel • Place pressure washer on a level surface. CAUTION Any attempt to crank or start the engine before it has been properly filled with the recommended oil will result in equipment failure. • Refer to engine manual for oil and fuel fill information. • Damage to equipment resulting from failure to follow this instruction will void warranty. • Refer to engine owner’s manual and follow oil and fuel recommendations and instructions. NOTE: Check oil often during engine break...
Questo manuale è adatto anche per i modelli :apparecchiature di lavaggio - 195764GS (2.01 mb)