valutazioni - , GPA: ( )

Istruzioni per l'uso Black & Decker, Modello PW1550

Produttore : Black & Decker
File Size : 5.38 mb
File Nome :

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

To prevent damage to the appliance, when running do not stop the water jet for more than 10 minutes at a time. 7.3 Stopping the appliance 1) Set the starter device switch on (OFF/0). 2) Depress the gun trigger and discharge the residual pressure inside the hoses. 3) Engage the gun safety catch (D). English 19 7.4 Restarting 1) Release the safety catch (D). 2) Depress the gun trigger and discharge the residual air inside the hoses. 3) Set the starter device on (ON/1). 7.5 Storage 1) Switch the appliance o (OFF/0). 2) Remove the plug from the socket. 3) Turn o the water supply tap. 4) Discharge the residual pressure from the gun until all the water has come out of the nozzle. 5) Drain the detergent tank. 6) Engage the gun safety catch (D). 7.6 Relling and using detergent When using detergent, the adjustable nozzle must be set on " " (on models with this feature). Fill the tank with highly degradable detergent. 7.7 Recommended cleaning procedure Dissolve dirt by applying the detergent mixed with water to the surface while still dry. When dealing with vertical surfaces work from the bottom upwards. Leave the detergent to act for 1-2 minutes but do not allow the surface to dry. Starting from the bottom, use the high pressure jet at a minimum distance of 30 cm. Do not allow the rinse water to run onto unwashed surfaces. 8 MAINTENANCE FIG.5 Any maintenance operations not covered by this chapter should be carried out by an Authorized Sales and Service Centre. Caution -Danger! Always disconnect the plug from the power socket before carrying out any work on the appliance. 8.1 Cleaning the nozzle 1) Disconnect the lance from the nozzle. 2) Remove any dirt deposits from the nozzle hole using the tool (C1). 8.2 Cleaning the lter Clean the suction lter (L) and the detergent lter after every 50 hours of operation. 8.3 Unjamming the motor (on models with this feature) In case of lengthy stoppages, limescale sediments may cause the motor to seize. To unjam the motor, turn the drive shaft with a tool (M). 8.4 End-of-season storage Treat the appliance with non-corrosive, non-toxic antifreeze before storing it away for winter. 20English 9 TROUBLESHOOTING Problem Possible causes Remedy Pump does not reach working pressure Nozzle worn Replace nozzle Water lter fouled Clean lter (g.5) Water supply pressure low Turn on water supply tap fully Air being sucked into system Check tightness of hose ttings Air in pump Switch o the appliance and keep depressing and releas- ing the gun trigger until the water comes out in a steady ow. Switch the appliance back on again. Adjustable nozzle not positioned correctly Turn the adjustable nozzle (E) (+) (g.3) Pressure drops during use Water intake from external tank Connect appliance to the mains water supply Intake water too hot Reduce temperature Nozzle clogged Clean nozzle (g.5) Motor “sounds” but fails to start Insucient power supply Check that the voltage of the mains power supply line is the same as that on the plate (g.2) Voltage loss due to use of extension cable Check characteristics of extension cable Appliance not used for a long period of time Contact your nearest Authorized Service Centre Problems with AS device Contact your nearest Authorized Service Centre Motor fails to start No electrical power Check that the plug is rmly in the socket and that the mains voltage supply is present (*) Problems with AS device Contact your nearest Authorized Service Centre Appliance not used for a long period of time Using the tool (L) unjam the motor from the hole at the rear of the appliance (in models with this feature) (g.5) Water leakage Seals worn Have the seals replaced at your nearest Authorized Service Centre Appliance noisy Water too hot Reduce temperature (see technical data Oil leakage Seals worn Contact your nearest Authorized Service Centre AS versions only: motor starts even with gun trigger is released Nozzle clogged Clean nozzle (g.5) High pressure system or pump hydraulic circuit not watertight Contact your nearest Authorized Service Centre AS versions only: no water delivery when gun trigger is depressed (with supply hose connected) Nozzle clogged Clean nozzle (g.5) If the motor starts and does not restart during operation, wait 2-3 minutes before repeating the start-up procedure (overload cutout has been tripped). If the problem recurs more than once, contact your nearest Authorized Service Centre. 21English 10 SERVICE authorized service locations. All Black & Decker Service Centers are Technical Data Output Pressure Maximum pressure Power T° input Maximum input pressure Repulsive force of the gun to the maximum pressure Motor Insulation Motor Protection Voltage Sound level: LPA (EN 60704-1) LWA (EN 60704-1) Unit vibrations Weight AR 230V~50Hz B2C 220V~50Hz B2 220V~60Hz B3 120V~60Hz BR 127V~60Hz Unit L/h Bar PW1550 360 85 MPa Bar 8,5 120 MPa W °C MPa N - - Db (A) Db (A) M/s2 kg 12 1500 50 1 9,4 Class F IPX5 81,2 89 3,72 8 and reliable power tool service. Whether you need technic...