valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
This will allow your detergent to attack the deep down dirt that has worked its way into the cleaning surface. Before triggering the gun, adjust the nozzle to a wide fan pattern and slowly adjust to the desired spray pattern. This will help 7 Operating Instructions and Parts Manual Operating Instructions and Parts Manual 3. Detergent Application Note: Use only detergents formulated for pressure washers. Test detergent in an inconspicuous area before use. 1. Unscrew caps from detergent bottles and fill bottles with detergent. Note: Bottles operate independently and can be filled with different detergents. 2. Replace caps on bottles. 3. Select detergent to be used by turning detergent selector knob on front of unit to either “I” or “II.” 4. Slide adjustable fan nozzle to low pressure position and apply detergent so that it thoroughly covers the cleaning surface. Apply from bottom to top to prevent detergent from sliding down and streaking. Wait a couple of minutes for the detergent to break down dirt and grime. This is a good time to use a brush to lightly scrub heavily soiled areas. Never allow detergent to dry on cleaning surface. Note: Detergent injection may not work with extension hose or replacement hoses longer than 25 feet. 5. To rinse or return to high pressure, release trigger and slide nozzle to high pressure position. 4. Final Rinse Start final rise at bottom and work upward. Make sure you thoroughly rinse the surface and that all detergent has been removed. 5. Shutdown 1. Be sure all detergent is flushed from system. 2. Turn off motor. 3. Turn off water supply. 4. After motor and water supply are turned off, trigger gun to depressurize system. 5. After each use, wipe all surfaces of the pressure washer with a clean, damp cloth. NEVER turn water supply off before turning motor off. Serious damage could occur to the pump and/or motor. NEVER disconnect high pressure discharge hose from machine while system is pressurized. To depressurize, turn motor off, turn water supply off and squeeze gun trigger 2–3 times. 8 PW1810 PW1810 Symptom Possible Cause(s) Corrective Action(s) Pressure washer does not start up 1. 2. 3. 4. 5. 6. Unit is pressurized 1. GFCI has tripped 2. Plug is not well 3. connected or electric socket is faulty Extension cord too 4. long or wire size too small Main voltage supply 5. too low Thermal safety switch 6. has tripped Squeeze trigger on gun Push reset button on plug Check plug, socket and fuses Remove extension cord Check that main supply voltage is adequate Switch off unit and allow motor to cool down Pump does not reach 1. Water inlet filter is 1. Clean water inlet filter necessary pressure clogged 2. Pump sucking air from 2. Check that connections hose connections and locking ring are properly tightened 3. Nozzle worn or not 3. Call 1-800-330-0712 correct size 4. Unloader clogged or 4. Call 1-800-330-0712 worn 5. Valves clogged or 5. Call 1-800-330-0712 worn Fluctuating 1. Pump sucking in air 1. Check that hoses and pressure connections are tight 2. Clogged nozzle 2. Clean with tip cleaner (see page 6 and 7) 3. Valves dirty, worn or 3. Call 1-800-330-0712 stuck 4. Water seals worn 4. Call 1-800-330-0712 Motor stops 1. Extension cord too 1. Remove extension cord suddenly long or wire size too small 2. Thermal safety switch 2. Check that main supply has tripped due to voltage corresponds to overheating specifications No detergent suction 1. Lance nozzle not in 1. Slide lance nozzle into low pressure position low pressure position (see page 6) 2. Using high pressure 2. Remove high pressure extension hose or high extension hose or use pressure hose is too high pressure hose short- long er than 25 feet 3. Injector clogged on 3. Call 1-800-330-0712 pump Unit begins to smoke Overheated, overloaded or damaged motor Turn off unit and call 1-800-330-0712 9 Operating Instructions and Parts Manual Operating Instructions and Parts Manual call 1-800-330-0712 Address any correspondence to: Please provide following Campbell Hausfeld information: Attn: Customer Service -Model number 100 Mundy Memorial Drive -Serial number (if any) Mt. Juliet, TN 37122 U.S.A. -Part description and number as shown in parts list 1 2 3 4 6 7 8 910 11 12 13 14 15 16 17 18 12 15 16 19 5 10 PW1810 PW1810 1 Gun PM344400SV 1 2 Hose PM344420SV 1 3 Quick connect lance PM343311SV 1 4 Quick connect fan nozzle PM343316SV 1 5 Quick connect turbo nozzle PM343313SV 1 6 Tip cleaner PM008500AV 1 7 Handle PM344401SV 1 8 Hardware pack PM344402SV 1 9 Left detergent bottle “I” PM344403SV 1 10 Right detergent bottle “II” PM344404SV 1 11 Detergent bottle cap PM344405SV 2 12 Hanger PM344406SV 2 13 Mesh bag PM344407SV 1 14 Base PM344408SV 1 15 Wheel PM344409SV 2 16 Hub cap PM344410SV 2 17 Axle PM344411SV 1 18 Rubber foot PM344412SV 2 19 O-ring PM232200SV 1 11 Operating Instructions and Parts Manual Operating Instructions and Parts Manual 1. DURATION: From t...
Questo manuale è adatto anche per i modelli :apparecchiature di lavaggio - IN468300AV (4.53 mb)