valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
Before spraying, check the item to be cleaned to assure yourself that it is strong enough to resist damage from the force of the spray. 9- ENG A00543 Changing Nozzles on Spray Wand DO NOT attempt to change nozzles while pressure washer is running. Turn engine off before changing nozzles. 1. Pull quick connect coupler back and insert nozzle. 2. Release quick connect coupler and twist nozzle to make sure it is secure in coupler. Risk Of Injury. Ensure nozzle is completely inserted in QC socket, and QC snap ring is fully engaged (forward) before squeezing gun trigger. Risk of injection or injury to person. Do not direct discharge stream toward persons, unprotected skin, eyes, or any pets or animals. Serious injury can occur. HOW TO APPLY CHEMICALS AND CLEANING SOLVENTS Applying chemicals or cleaning solvents is a low pressure operation. NOTE: Use only soaps and chemicals designed for pressure washer use. Do not use bleach. To Apply chemicals: 1. Press chemical hose onto barbed fitting located near high pressure hose connection of pump as shown. Barbed Fitting 2. Place other end of chemical hose with filter on it into container holding chemical/cleaning solution. NOTE: For every 7 gallons of water pumped 1 gallon of chemical/cleaning solution will be used. 3. Install low pressure (black) nozzle into quick connect fitting of spray wand, see How To Use Spray Wand paragraph in this section. 4. After use of chemicals, place chemical hose into container of clean water and draw clean water through chemical injection system to rinse system thoroughly. If chemicals remain in the pump it could be damaged. Pumps damaged due to chemicals will not be covered under warranty. NOTE: Chemicals and soaps will not siphon when spray wand is in the high pressure setting. STARTING Prior to starting, refer to your engine manual for proper starting procedure. 1. In a well ventilated outdoor area add fresh, high quality, unleaded gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. Refer to Engine Owners Manual for correct procedure. 2. Check engine oil level. See Engine Owners Manual for correct procedure. NOTE: There will be a slight amount of oil in the engine from factory testing. 3. Verify the filter screen is in water inlet of pump. NOTE: Cone side faces out. Filter Screen A00543 10- ENG STARTING (continued) 4. Connect water source to pump inlet. NOTE: Water source must provide a minimum of 5 gallons per minute at 20 PSI. 5. Connect high pressure hose to pump outlet. High Pressure Hose Water Source 6. If applying a chemical or cleaning solution, see How To Apply Chemicals/Cleaning Solvents instructions in this section. 7. Turn water source on. NOTE: Failure to do so could cause damage to the pump. 8. Start engine. See Engine Owners Manual for correct procedure. NOTE: When engine rope is pulled, pressure starts building in the gun. If the engine does not start after two pulls, pull the gun trigger to relieve this pressure. 9. Depress trigger on gun to start water flow. NOTE: Stand on a stable surface and grip gun/spray wand firmly with both hands. Expect the gun to kick when triggered. 10. Release trigger to stop water flow. 11. Adjust spray for the task being performed by changing quick connect nozzle. See How To Use Spray Wand instructions in this section. SHUTTING DOWN 1. After each use, if you have applied chemicals, place chemical hose into container of clean water and draw clean water through chemical injection system to rinse system thoroughly. NOTE: Failure to do so could cause damage to the pump. 2. Turn engine off. See Engine Owner’s Manual. NOTE: NEVER turn the water off with the engine running. 3. Turn water source off. 4. Pull trigger on spray gun to relieve any water pressure in hose or spray gun. 5. See Storage section in this manual for proper storage procedures. MAINTENANCE When performing maintenance, you may be exposed to hot surfaces, water pressure, or moving parts that can cause serious injury or death! Before performing any maintenance or repair, disconnect spark plug wire, let engine cool and release all water pressure. The engine contains flammable fuel. DO NOT smoke or work near open flames while performing maintenance. To ensure efficient operation and longer life of your pressure washer, a routine maintenance schedule should be prepared and followed. If the pressure washer is used in unusual conditions, such as high-temperatures or dusty conditions, more frequent maintenance checks will be required. ENGINE Consult the Engine Owners Manual for the manufacturer's recommendations for any and all maintenance. NOTE: The frame is equipped with an oil drain hole to help make changing the engine oil easier. 11- ENG A00543 PUMP NOTE: The pump was filled with oil at the factory. 1. Change pump oil after the first ten (10) hours of operation and every fifty (50) hours thereafter. To Check Oil: 1. Remove dipstick/oil plug from pump and wipe clean. 2....
Questo manuale è adatto anche per i modelli :apparecchiature di lavaggio - A00543 (972.62 kb)