Log:
valutazioni - 1, GPA: 3 ( )

Istruzioni per l'uso Porter-Cable, Modello A08058-0412-0

Produttore : Porter-Cable
File Size : 2 mb
File Nome : 66a2fa64-e62a-4b6a-a450-c660544d86e4.pdf
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


NOTE: Using a pump protector/ winterizer or *RV antifreeze is to provide proper lubrication to the internal seals of the pump regardless of temperature or environment. PRESSURE WASHER 1. Drain all water from high pressure hose. 2. Drain all water from spray gun and wand by holding spray gun in a vertical position with nozzle end pointing down and squeezing trigger. Store in gun holder. 3. Store chemical hose so it is protected from damage. 1. Obtain a funnel, six ounces of *RV antifreeze, and 16 - 36 inches of garden hose with a male hose connector attached to one end. Use only RV antifreeze. Any other antifreeze is corrosive and can damage pump. 2. Disconnect spark plug wire. 3. Connect length of garden hose to water inlet of pump. 4. Add *RV antifreeze to hose as shown. 5. Pull engine starter rope slowly several times until antifreeze comes out of high pressure hose connection of pump. 6. Remove garden hose from water inlet of pump. 7. Reconnect spark plug wire. *Windshield washer fluid may also be used TROUBLE SHOOTING GUIDE CAUSE CORRECTION PROBLEM Add Fuel. No fuel. Engine will not start (see Engine Manual for further engine troubleshooting) Add required amount of oil. Low oil Squeeze gun trigger to relieve pressure. Pressure builds up after two pulls on the recoil starter or after initial use. Move choke to the "Choke" position. Choke lever in the "No Choke" position. Attach spark plug wire. Spark plug wire not attached. Place engine ON/OFF switch in ON position. Engine ON/OFF switch in OFF position. Choke lever in the "Choke" position on a "hot" engine or an engine that has been exposed to thermal heat for a long period of time. Move choke to the "No Choke" position. Fuel valve closed Move the fuel valve lever to the "Open" position. No or low pressure (initial use) See How to Use Spray Wand instructions in the Operation Section. Spray wand not in high pressure. Low water supply. Water supply must be at least 5 GPM @ 20 PSI. Leak at high pressure hose fitting. Repair leak. Apply sealant tape if necessary. Nozzle obstructed. See Nozzle Cleaning instructions in the Maintenance section. Remove and clean filter. Water filter screen clogged. Check with Authorized Warranty Service Center (AWSC.) Defective E-Z start valve. Turn off the engine, then the water source. Disconnect the water source from the pump inlet and turn the water source on to remove all air from the hose. When there is a steady stream of water present, turn water source off. Re-connect water source to pump inlet and turn on water source. Squeeze trigger to remove remaining air Air in hose. Choke lever in the "Choke" position. Move choke to the "No Choke" position. High pressure hose is too long. Use high pressure hose under 100 feet. CAUSE CORRECTION PROBLEM See How to Use Spray Wand paragraph in the Operation Section. Spray wand not in low pressure. Will not draw chemicals Chemical filter clogged. Clean filter. Make sure end of chemical hose is fully submerged into cleaning so...

Questo manuale è adatto anche per i modelli :
apparecchiature di lavaggio - A08058-0412-0 (2 mb)
apparecchiature di lavaggio - A08058-0412-0 (2 mb)
apparecchiature di lavaggio - A08058-0412-0 (2 mb)
apparecchiature di lavaggio - A08058-0412-0 (2 mb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie