valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket. A - LCD Display B - Wall Bracket C - Wall Wall Bracket Angle Adjustment Adjust the bracket angle to -2* before installing it on the wall. 1. Fix the product to the wall bracket. 2. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle. I Note You can adjust the bracket angle between -2* and 15*. Introduction Make sure to use the top center, and not the left or the right side of the product to adjust the angle. Remote Control (RS232C) Cable connections interface RS232C(9 pin) pin TxD(No.2) RxD(No.3) GND(No.5) Bits rate 9600 bps Data Bits 8 bit Parity None Stop Bits 1 bit Flow control None Maximum length 15 m (only shielded type) • Pin assignment O “T Pin Signal 1 Data Carrier Detect 2 Received Data 3 Transmitted Data 4 Data Terminal Ready 5 Signal Ground 6 Data Set Ready 7 Request to Send 8 Clear to Send 9 Ring Indicator RS232C cable Introduction Connector : 9-pin D-Sub Cable : Cross (reversed) cable -P1- -P1- -P2- -P2- FEMALE Rx 2 .—> 3 Rx FEMALE Tx 3 <-„. 2 Tx Gnd 5 5 Gnd Connecting method Control codes • Get control Header command 0xAA command type ID DATA Length 0 CheckSum Set control Header command DATA DATA ID Length CheckSum 0xAA command type 1 Value • commanding words No. command type command Value range 1 Power control 0x11 0~1 Introduction 2 Volume control 0x12 0 1 0 o 3 Input source control 0x14 - 4 Screen Mode control 0x18 - 5 Screen Size control 0x19 0~255 6 PIP on/off control 0x3C 0~1 7 Auto adjustment control 0x3D 0 8 Video wall Mode control 0x5C 0~1 9 Safety Lock 0x5D 0~1 - ID should show hexadecimal value of assigned ID, but ID 0 should be 0xFF. - Every communication will be made in hexadecimals and Checksum is the sum of all remainings. If it exceeds two digits,for example, it is 11+FF+01+01=112, discard the number in the first digit like below. example)PowerOn&ID=0 Header command ID DATA Length DATA 1 CheckSum 0xAA 0x11 1 Power Header command ID DATA Length DATA 1 12 0xAA 0x11 1 1 If you want to control every mechanism connected with Serial Cable regardless of its ID, set ID part to "0xFE" and send commands. At the time, each product will follow commands but it will not respond with ACK. • Power Control • Function Personal Computer turns TV / Monitor power ON/OFF. • Get Power ON/OFF Status Header command 0xAA 0x11 ID DATA Length 0 CheckSum • Set Power ON/OFF Header command ID DATA Length DATA CheckSum 0xAA 0x11 1 Power Power : Power code to be set on TV / Monitor 1 : Power ON 0 : Power OFF Introduction • Ack Header command ID DATA Length Ack/Nak r-CMD Vall 0xAA 0xFF 3 ‘A’ 0x11 Power Check Sum Power : Same as above • Nak Header command ID DATA Length Ack/Nak r-CMD Vall 0xAA 0xFF 3 ‘N’ 0x11 ERR Check Sum ERR : Error code that shows what occurred error is • Volume Control • Function Personal Computer changes volume of TV / Monitor. • Get Volume Status Header command 0xAA 0x12 ID DATA Length 0 CheckSum • Set Volume Header command ID DATA Length DATA CheckSum 0xAA 0x12 1 Volume Volume : Volume value code to be set on TV / Monitor (0 ~ 100) • Ack Header command ID DATA Length Ack/Nak r-CMD Val1 0xAA 0xFF 3 ‘A’ 0x12 Volume Check Sum Volume : Same as above • Nak Header command ID DATA Length Ack/Nak r-CMD Val1 0xAA 0xFF 3 ‘N’ 0x12 ERR Check Sum ERR : Error code that shows what occurred error is Introduction • Input Source Control • Function Personal Computer changes input source of TV / Monitor. • Get Input Source Status Header command 0xAA 0x14 ID DATA Length 0 CheckSum • Set Input Source Header command ID DATA Length DATA CheckSum 0xAA 0x14 1 Input Source Input Source : Input Source code to be set on TV / Monitor 0x14 PC 0x1E BNC 0x18 DVI 0x0C AV 0x04 S-Video 0x08 Component 0x20 MagicInfo 0x1F DVI_VIDEO 0x30 RF(TV) 0x40 DTV 0x21 HDMI1 0x22 HDMI1_PC 0x23 HDMI2 0x24 HDMI2_PC 0x25 DisplayPort A Caution DVI_VIDEO, HDMI1_PC, HDMI2_PC ^ Get Only In the case of MagicInfo, only possible with models include MagicInfo In the case of TV, only possible with models include TV. • Ack Header command ID DATA Ack/Nak r-CMD Val1 Check Length Sum Introduction 0xAA 0xFF 3 ‘A’ 0x14 Input Source Input Source : Same as above • Nak Header command ID DATA Length Ack/Nak r-CMD Vall 0xAA 0xFF 3 ‘N’ 0x14 ERR Check Sum ERR : Error code that shows what occurred error is Screen Mode Control Function Personal Computer changes "Screen Mode" of TV/Monitor. Cannot be controlled when Video Wall is on. A Caution Only works with models include TV. Get Screen Mode Status Header command 0xAA 0x18 ID DATA Length 0 CheckSum Set Picture Size Header command ID DATA Length DATA CheckSum 0x...
Questo manuale è adatto anche per i modelli :Monitor - 460TS-3 (6.19 mb)