valutazioni - 5, GPA: 3.6
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
B Power port Connect the power cable here. C Power switch Use this switch to turn the monitor On and Off. D MIC OUT jack Connect a cable here to send sound from the internal microphone to the computer’s sound card. E AUDIO IN jack Connect a cable here to bring sound from your computer’s sound card. OUT IN MIC AUDIO A B C D E F G Setting up Your Monitor Setting up Your Monitor Table 1. Connector locations for multimedia bases (Continued) Item Name Description F External microphone jack Connect an external microphone here. Using an external microphone automatically disconnects the monitor’s internal microphone. G Headphone jack Connect headphones here. Connecting headphones automatically turns the speakers off. Plug and Play Our adoption of the new VESA® Plug and Play solution eliminates complicated and time consuming setup. It allows you to install your monitor in a Plug and Play compatible system without the usual hassles and confusion. Your PC system can easily identify and configure itself for use with your display. This monitor automatically tells the PC system its Extended Display Identification (EDID) data using Display Data Channel (DDC) protocols so the PC system can automatically configure itself to use the flat panel display. If your PC system needs a video driver, following the instructions given below according to the operating system your computer uses. Installing the Video Driver When prompted by the operating system for the monitor driver, insert the Driver diskette included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Windows® 98 Windows® 98 will auto-detect your new monitor and start the “Add New Hardware 1 Wizard” if the drivers are not already installed. Click the NEXT button to search for drivers. Check the diskette drive box to install the drivers off the diskette provided with your 2 FPD monitor and click NEXT. Confirm that Windows found the driver on the diskette and click NEXT again to install 3 the driver. To manually install or update the driver, follow the directions below: Click on START, SETTINGS, CONTROL PANEL, DISPLAY SETTINGS tab, 1 ADVANCED, MONITOR tab, CHANGE. This will start the “Add New Hardware Wizard”. Follow the same directions as given in the steps in the section above. 2 8 Setting up Your Monitor Windows® 95 To determine the version of Windows® 95 that your computer uses, right click on the “My Computer” icon on the Windows desktop and select “Properties”. The version number can be seen on the “General” section under “System:”. Follow the directions given below according to the version of your Windows® 95 operating system: Version 4.00.950A Click on START, SETTINGS, CONTROL PANEL, DISPLAY SETTINGS tab, 1 CHANGE DISPLAY TYPE, CHANGE, HAVE DISK. Type the diskette drive letter in the box and click OK. 2 Version 4.00.950B Click on START, SETTINGS, CONTROL PANEL, DISPLAY, ADVANCED 1 PROPERTIES, MONITOR tab, HAVE DISK. Type the diskette letter in the box and click OK. 2 Self-Test Feature Check (STFC) Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. If your monitor and computer are properly connected but the monitor screen remains dark and the power indicator is blinking, run the monitor self-test by performing the following steps: Turn off both your computer and the monitor. 1 Unplug the video cable from the back of the computer. 2 Turn on the monitor. 3 9 English Setting up Your Monitor If the monitor is functioning properly, you will see a white box with a red border and black text inside as shown in the following illustration: Check Signal Cable No Connection Figure 5. Monitor self test screen The three boxes inside the border are red, green and blue. Failure of any of the boxes to appear indicates a problem with your monitor. This box also appears during normal operation if the video cable becomes disconnected or damaged. Turn off your monitor and reconnect the video cable; then turn on both your computer 4 and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly. Getting Help If your monitor does not display an image, check your cable connections and refer to “Troubleshooting” on page 21. If you experience difficulties with the quality of the displayed image, run Auto Adjustment (see page 12) and refer to “Adjusting Your FPD” on page 11 or “Troubleshooting” on page 21. Warm-up Time All FPD monitors need time to become thermally stable the first time you turn them on each day. Therefore, to achieve more accurate adjustments for parameters, allow the FPD monitor to warm (be on) for at least 20 minutes before making any screen adjustments. Adjusting Your FPD User Controls Your flat panel display allows you to easily adjust the characteristics of the image being displa...