valutazioni - 3, GPA: 4.7
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
(Do not use chemicals such as benzene, paint thinners or alcohol) Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame; wipe in one direction only. Too much moisture may cause staining. On Repacking Do not throw away the carton and packing materials. They make an ideal container in which to transport the unit. When shipping the unit to another location, repack it in its original material. On Disposal The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority. 3 4 Accessories !!! Thank for selecting LGE products !!! Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. User's Guide/Cards Power Cord 15-pin D-Sub Signal Cable (To set it up, this signal cable may be attached to this product before shipping out.) DVI-D Signal Cable (This feature is not available in all countries.) (Only E1910T/E2210T ) NOTE This accessories may look different from those shown here. User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite cores to maintain standard compliance for the product. Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand 1. Place the monitor with its front facing downward on a soft cloth. 2. Assemble the Stand Body into the 3. Assemble the Stand Base(Front, product in the correct direction as shown in Rear) into the Stand Body in the the picture. Make sure you push it until you correct direction. hear it “click”. Stand Body Hinge Body Stand Body Stand Base 4. Tie down the base lock to perpendicularity direction. 5. Once assembled take the monitor up carefully and face the front side. 5 Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on aflat 2. Place the monitor face Down on the surface. cushion or soft cloth. 3. Change your lock on the product as it follows and turn it in the arrow direction. .. If you can't release the stand base even the locking knob is at a release position, Please push the indicated knob down and retry it. 6 Connecting the Display 4. Pull out the Stand to remove. 5. Pushing the PUSH button, Take the stand body from hinge body. Good Position Bad Position Warning: You can hurt your finger. 7 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display -After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5° to 15° ERGONOMIC It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. Do not touch or press the screen when adjusting the angle of the monitor. When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). 8 Connecting the Display E1910T/E2210T Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2. Connect signal input cable 1 and power cord 2 in order, then tighten the screw of the signal cable. Connect DVI-D(Digital signal) Cable Connect D-sub(Analog signal) Cable A B AB Wall-outlet type Mac adapter : For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. When using a D-Sub signal input cable connector for Macintosh Varies according to model. NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. 3. Press the power button on the front panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' (Only Analog Mode) Power Button Connect the signal input cable and tighten it up by turning in the direction of the arrow as shown in the figure. NOTE ‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. ‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing scre...
Questo manuale è adatto anche per i modelli :Monitor - E1910T (4.51 mb)
Monitor - E2210T (4.51 mb)
Monitor - E2210T-BN (4.51 mb)