valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
• You might like to save the package box and packing material for shipping the display. 1.3. Installation Notes • Due to the high power consumption, always use the plug exclusively designed for this product. If an extended line is required, please consult your service agent. • The product should be installed on a flat surface to avoid tipping. The distance between the back of the product and the wall should be maintained for proper ventilation. Avoid installing the product in the kitchen, bathroom or any other places with high humidity so as not to shorten the service life of the electronic components. • The product can normally operate only under 3000m in altitude. In installations at altitudes above 3000m, some abnormalities may be experienced. 1.4. Installing and Removing Table Stands (optional) To install table stands: 1. Ensure your display is powered off. 2. Spread a protective sheet on a flat surface. 3. Grab the carrying handles and place the display face-down on the protective sheet. 4. After inserting the stand in the guide block, tighten the screws on both sides of the display. NOTE: The longer side of the stand should face the front of the display. Carrying handleThumbscrewsLonger portions face the frontTable stand To remove table stands: 1. Power off the display. 2. Spread a protective sheet on a flat surface. 3. Grab the carrying handles and place the display face-down on the protective sheet. 4. Remove screws using a screwdriver and place them in a safe place for reuse. 1.5. Mounting on a Wall To mount this display to a wall, you will have to obtain a standard wall-mounting kit (commercially available). We recommend using a mounting interface that complies with TUV-GS and/or UL1678 standard in North America. Protective SheetVESA GridTabletop standTable 1. Lay a protective sheet on a table, which was wrapped around the display when it was packaged, beneath the screen surface so as not to scratch the screen face. 2. Ensure you have all accessories for mounting this display (wall mount, ceiling mount, table stand, etc). 3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could result in damage to the equipment or injury to the user or installer. Product warranty does not cover damage caused by improper installation. 4. For the wall-mounting kit, use M6 mounting screws (having a length 10 mm longer than the thickness of the mounting bracket) and tighten them securely. 1.5.1. VESA Grid BDL4250EL 400(H) x 200(V) mm 200(H) x 200(V) mm BDL4650EL 400(H) x 400(V) mm 400(H) x 200(V) mm 200(H) x 200(V) mm Caution: To prevent the display from falling: • For wall or ceiling installation, we recommend installing the display with metal brackets which are commercially available. For detailed installation instructions, refer to the guide received with the respective bracket. • To lessen the probability of injury and damage resulting from fall of the display in case of earthquake or other natural disaster, be sure to consult the bracket manufacturer for installation location. Ventilation Requirements for enclosure locating To allow heat to disperse, leave space between surrounding objects as shown in the diagram below. 100 mm100 mm100 mm100 mm 1.6. Mounting in Portrait Position This display can be installed in portrait position. 1. Remove the table stand, if attached. 2. Rotate 90 degrees clockwise. The “” logo should be on the LEFT side when facing the display. 9090 1.6.1. How to use the logo guider for portrait position 1. Put the guider on the lower-left corner of the front bezel of the display. Fold down both of its edges. 2. Peel off the protective film at the back of the “” logo sticker. Hold and press the guider with your left hand. Put the “” logo sticker with its adhesive side down into the logo hole with your right hand, and press to make it stick tightly onto the front bezel. 3. Remove the guider. 1.6.2. How to remove the logo 1. Prepare a piece of paper with a cutting area of logo as a protector to prevent the front bezel from scratching. 2. Using a knife, carefully remove the logo sticker with the paper placing beneath. 3. Tear off the logo sticker. 123 NOTE: When installing the display on a wall, please consult a professional technician for proper installation. We accept no liability for installations not performed by a professional technician. 2. Parts and Functions 2.1. Control Panel 12345678MUTEINPUTMENU9 1 POWER button Use this button to turn the display on or put the display to standby. 2 MUTE button Switch the audio mute ON/OFF. 3 INPUT button • Use this button to select the input source. 4 [] button Increase the adjustment while OSD menu is on, or increase the audio output level while OSD menu is off. • Used as [SET] button in the On-Screen-Display menu, 5 [] button Decrease the adjustment while OSD menu is on, or decrease the audio output level while OSD menu is off. 6 [] button Move the highlight bar up to adjust the selected item...
Questo manuale è adatto anche per i modelli :Monitor - BDL4650EL/00 (4.53 mb)