valutazioni - 1, GPA: 3 ( )

Produttore : AMX File Size : 3.29 mb File Nome : Modero.1200V.OperationReferenceGuide.pdf Lingua di insegnamento:

Set the page flip Syntax: password. "'@PWD-'" Variables: page flip password = 1 - 50 ASCII characters. Example: SEND COMMAND Panel,"'@PWD-Main'" Sets the page flip password to 'Main'. ^PWD Password level is required and must be 1 - 4. Set the page flip Syntax: password. "'^PWD-,'" Variables: password level = 1 - 4. page flip password = 1 - 50 ASCII characters. Example: SEND COMMAND Panel,"'^PWD-1,Main'" Sets the page flip password on Password Level 1 to 'Main'. @RPP @RPP resets the protected password to its default (1988). Reset the Syntax: protected "'@RPP'" password. Example: SEND COMMAND Panel,"'@RPP'" Resets the protected Setup page password to ‘1988’. ^VOL Syntax: Set the panel "'^VOL-'" volume. Variable: volume level = 0 - 100. 100 is maximum volume setting. Example: SEND_COMMAND Panel,"'^VOL-50'" Set the panel volume to 50. NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Programming Dynamic Image Commands The following table describes Dynamic Image Commands. Dynamic Image Commands ^BBR Syntax: Set the bitmap of "'^BBR-,,'" a button to use a Variable: particular variable text address range = 1 - 4000. resource. button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons 1 = Off state and 2 = On state). resource name = 1 - 50 ASCII characters. Example: SEND_COMMAND Panel,"'^BBR-700,1,Sports_Image'" Sets the resource name of the button to ’Sports_Image’. ^RAF Adds any and all resource parameters by sending embedded codes and data. Add new Since the embedded codes are preceded by a '%' character, any '%' character contained resources. in the URL must be escaped with a second '%' character (see example). The file name field (indicated by a %F embedded code) may contain special escape sequences as shown in the ^RAF, ^RMF - Embedded Codes table below. Syntax: "'^RAF-,'" Variables: • resource name = 1 - 50 ASCII characters. • data = Refers to the embedded codes, see the ^RAF, ^RMF - Embedded Codes section on page 153. Example: SEND_COMMAND Panel,"'^RAF-New Image,%P0%HAMX.COM%ALab/ Test%%5Ffile%Ftest.jpg'" Adds a new resource. • The resource name is ’New Image’ • %P (protocol) is an HTTP • %H (host name) is AMX.COM • %A (file path) is Lab/Test_file • %F (file name) is test.jpg. Note that the %%5F in the file path is actually encoded as %5F. ^RFR Syntax: Force a refresh for "'^RFR-'" a given resource. Variable: resource name = 1 - 50 ASCII characters. Example: SEND_COMMAND Panel,"'^RFR-Sports_Image'" Forces a refresh on ’Sports_Image’. NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Programming Dynamic Image Commands (Cont.) ^RMF Modifies any and all resource parameters by sending embedded codes and data. Modify an Since the embedded codes are preceded by a '%' character, any '%' character contained existing resource. in the URL must be escaped with a second '%' character (see example). The file name field (indicated by a %F embedded code) may contain special escape sequences as shown in the ^RAF, ^RMF - Embedded Codes section on page 153. Syntax: "'^RMF-,'" Variables: • resource name = 1 - 50 ASCII characters • data = Refers to the embedded codes, see the ^RAF, ^RMF - Embedded Codes section on page 153. Example: SEND_COMMAND Panel,"'^RMF-Sports_Image,%ALab%%5FTest/ Images%Ftest.jpg'" Changes the resource ’Sports_Image’ file name to ’test.jpg’ and the path to ’Lab_Test/ Images’. Note that the %%5F in the file path is actually encoded as %5F. ^RSR Syntax: Change the "'^RSR-,'" refresh rate for a Variable: given resource. resource name = 1 - 50 ASCII characters. refresh rate = Measured in seconds. Example: SEND_COMMAND Panel,"'^RSR-Sports_Image,5'" Sets the refresh rate to 5 seconds for the given resource (’Sports_Image’). ^RAF, ^RMF - Embedded Codes The ^RAF and ^RMF commands add and modify any and all resource parameters by sending embedded codes and data: "'^RAF-,'" "'^RMF-,'" The variable uses the embedded codes described in the following table: ^RAF, ^RMF - Embedded Codes Parameter Embedded Code Description protocol ’%P <0-1>’ Set protocol. HTTP (0) or FTP (1). user ’%U ’ Set Username for authentication. password ’%S ’ Set Password for authentication. host ’%H ’ Set Host Name (fully qualified DNS or IP Address). file ’%F ’ Full path to the location of the file or program that will return the resource. The path must be a valid HTTP URL minus the protocol and host. The only exception to this is the inclusion of special escape sequences and in the case of FTP protocol, regular expressions. path ’%A ’ Set Directory path. The path must be a valid HTTP URL minus the protocol, host and filename. The only exception to this is the inclusion of special escape sequences and in the ...

Scarica la tua

Per scaricare, digitare 2 cifre :