valutazioni - 3, GPA: 3.3 ( )

Produttore : Electrolux File Size : 315.07 kb File Nome : FF1061W.pdf Lingua di insegnamento:

This will reduce the possibility of a malfunction in the cooling system from handling during transportation. ? Clean the interior surface with lukewarm water using a soft cloth. • Installation of Your Appliance ? Place your refrigerator-freezer on a floor that is strong enough to support the refrigerator freezer when it is fully loaded. To level your refrigerator-freezer, adjust the leveling legs at the bottom of unit. ? Allow 2 inches of space between the back and sides of the unit, which allows the proper air circulation to cool the compressor and condenser. ? Locate the unit away from direct sunlight and sources of heat (stove, heater, radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption. Extreme cold ambient temperatures may also cause the refrigerator-freezer not to perform properly. ? Avoid locating the unit in moist areas. ? Plug the unit into an exclusive properly installed-grounded wall outlet. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a certified electrician or an authorized Avanti Products service center. 9 • Electrical Connection Warning• Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, have it replaced by an authorized Avanti Products service center. This unit should be properly grounded for your safety. The power cord of this unit is equipped with a three-prong plug which mates with standard three prong wall outlets to minimize the possibility of electrical shock. Do not under any circumstances cut or remove the third ground prong from the power cord supplied. For personal safety, this appliance must be properly grounded. This unit requires a standard 115/120 Volt AC ~/60Hz electrical outlet with three-prong ground. Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded. When a standard 2-prong wall outlet is encountered, it is your responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. The cord should be secured behind the unit and not left exposed or dangling to prevent accidental injury. The unit should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating label on the appliance. This provides the best performance and also prevent overloading house wiring circuits that could cause a fire hazard from overheated. Never unplug the unit by pulling the power cord. Always grip the plug firmly and pull straight out from the receptacle.Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. When moving the unit, be careful not to damage the power cord. • Extension Cord Because of potential safety hazards under certain conditions, it is strongly recommended that you do not use an extension cord with this unit. However, if you must use an extension cord it is absolutely necessary that it be a UL/CUL-Listed, 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 115 volts and at least 10 amperes. • Reversing the Door Swing of Your Appliance This refrigerator-freezer has the capability of the door opening from either the left or right side. The unit is delivered to you with the door opening from the left side. Should you desire to reverse the opening direction, please call service for reversal instructions. 10 OPERATING YOUR APPLIANCE • Temperature Control Panels • Setting the Temperature Control ? To control the internal temperature, adjust the control dial according to the ambient temperature or purpose of use. ? The first time you turn the unit on, set the temperature control to “7” in refrigerator section and “MAX” in freezer section. ? The range of the temperature control is from position “1” the warmest to “7” the coldest in refrigerator section and from position “1”the warmest to “6” the coldest in the freezer section. After 24 to 48 hours, adjust the temperature control to the setting that best suits your needs. The setting of “4” in refrigerator section and middle of “1” and “6” in freezer section should be correct for home or office refrigerator use. NOTE: • IF THE UNIT IS UNPLUGGED, HAS LOST POWER , OR IS TURNED OFF, YOU MUST WAIT 3 TO 5 MINUTES BEFORE RESTARTING THE UNIT. IF YOU ATTEMPT TO RESTART BEFORE THIS TIME DELAY, THEREFRIGERATOR -FREEZER WILL NOT START. • TURNING THE REFRIGERATOR TEMPERATURE CONTROL TO “OFF” POSITION STOPS THE COOLING CYCLE BUT DOES NOT SHUT OFF THE POWER TO THE UNIT. • Using Your Ice Cube Tray ? Recommended thermostat setting for ice making is position “6”. ? Fill the ice cube tray (two thirds of it) with cold water or with any liquid suitable for freezing and place the ...

Scarica la tua

Per scaricare, digitare 2 cifre :