valutazioni - 5, GPA: 4.2
(
)
)
|
Facilità d'uso
o READ SAFETY INSTRUCTION BOOKLET BEFORE USING THE PRODUCT o Go to for product registration. GENERAL CONTROLS 1. Power Cable: This power cable should be plugged into a wall receptacle AFTER all audio connections are made. 2. RCA Audio Output Cables: These cables should be plugged into the audio inputs of your home stereo system. (Please note: you can still copy records to your computer, even if the audio outputs of the turntable are not connected to a stereo system. It is also possible to hear your records through your computer, as long as you have configured your computer’s sound input and output options correctly and enabled Software Playthrough in the Audacity software. Please see the Software Guide for more information on configuring your computer to play the audio from the turntable. IMPORTANT: There is a switch on the bottom panel, next to the RCA cables that selects between PHONO/LINE. Use PHONO level for plugging into a turntable input on a home stereo. Use the LINE level for plugging into CD/AUX/TAPE inputs. WARNING: You may damage your receiver if you plug in a LINE level into a PHONO input. 3. USB Audio Output: Use the included USB Cable to connect your turntable to your computer. Refer to the software instruction guide before plugging in your turntable. 4. Power Button: This ring around the power button illuminates red when the turntable is switched on. 5. Platter: This platter must be securely fastened to the turntable prior to operation. The Motor Drive Belt can be found on the drive ring underneath the platter. See SETUP INSTRUCTIONS for detailed information on installing the Motor Drive Belt. 6. Start/Stop Buttons: These buttons start and stop the turntable motor. Both buttons have the same function. If they seem to not be functioning, check to make sure that the Motor Drive Belt is properly installed in the SETUP INSTRUCTIONS. 7. 1/8” Stereo Line Input: Connect Tape Players, Reel to Reel, or any other audio source here. This signal is sent to the computer through the USB. Make sure that your phono cartridge is installed while using this input for maximum sound quality. Also make sure that your RCA jacks are either plugged into an input device or not in contact with metal. Note: The 1/8" audio input is not routed to the turntable's RCA output jacks, only to your computer via USB. 8. 33 and 45 RPM Buttons: These buttons control the RPM of the turntable platter. A red LED indicates which RPM mode has been selected. NOTE: If the turntable is powered down while in the 45 RPM setting, it will return to 33 RPM when it is powered up. Note: You can record your 78RPM records by recording them at 33 or 45rpm, then changing them to 78 in the Audacity software. 9. Pitch LED: This LED illuminates green when the pitch slider is set at 0%. When the pitch slider is moved away from zero, the LED illuminates red. 10. Pitch Slider: This slide control allows the pitch to be increased or decreased by 10%. In the center position the pitch is at 0%. When moved away from the center and towards the tone arm decreases the pitch (slows down the platter) and moving the pitch slider away from the tone arm increase the pitch (speeds up the platter.) TONE ARM: Items 11 – 15 are all parts of the tonearm. Refer to the TONEARM SETUP section for additional details on these controls. 3 4 11. Counter Weight and Scale Ring: The Counterweight is used to balance the head shell and cartridge assembly so that the proper amount of stylus pressure is applied to the record. 12. Anti-Skate Adjustment: This knob is used to compensate for inward tracking forces. See TONEARM SETUP for more details. 13. Arm Clip: This specially designed arm clip secures the tone arm while at rest or when not in use. The arm clip has been designed to remain in the up position while unlocked. NOTE: When transporting the turntable, it is always recommended that the headshell be removed and the arm clip secured to prevent tonearm or turntable damage. 14. Tone Arm Lock Nut: This Aluminum nut is used to secure the head shell and cartridge assembly to the tone arm tube. See Cartridge Setup for more details. 15. Cartridge and Headshell: The cartridge is pre-mounted on a standard headshell. The cartridge is user replaceable and compatible with a variety of standard cartridges. Be sure to remove the clear plastic cover before operating the turntable from the cartridge. PLATTER SETUP WARNING: Incorrect Platter setup can lead to poor turntable performance, platter instability or permanent motor damage. 1. Start by placing the rubber drive belt around the inner bottom ring of the turntable platter. This should come preinstalled, but check to make sure that it is not twisted or damaged. 2. Install the Platter on the center spindle and press it down firmly. Check to make sure that it rotates uniformly and does not wobble excessively. 3. Rotate the platter so that the one of the holes is aligned with the Start Stop button on the front corner of the tu...