valutazioni - 1, GPA: 4
(
)
)
|
Facilità d'uso
IMPORTANT: Operation in Manual Mode re" quires the turntable connection to Remote Control only. The Turntable Sync Cable should be disconnected from the jack “M” on the control panel. To shoot in Manual Mode proceed as follows: 1. Switch on the turntable by pressing the red ON/OFF (I/O) button on the power panel. Figure 10.1 2. Choose «М» mode by pressing the «Mode» button. Figure 10.2 M10. ANUAL MODE M10. ANUAL MODE 3. Choose the required quantity of frames (8, 16, 32) by pressing the «Frame» button. Figure 10.3 4. Take the first picture with the camera. Figure 10.4 5. Press one of the buttons on the remote control to set the direction of rotation. After Figure 10.5 that the rotating surface of the turntable will move to the next frame. Indication of the digital display located on the control panel will increase by one. 6.If required the bad shot may be taken again. With this aim press the other button control rotation on the remote control. The turntable will go back to the previous shot position. Take the picture. Then press the first rotation controlling button to resume the movement of the turntable in the previ" ously set direction. Figure 10.6 6. Take the next picture after the rotation has ceased. 7. Depress the button on the remote control once again and take the pictures one by one in each point of photography until ro" tation is completed. Indication of the digital display on the control panel should coin" cide with the set number of frames in the series. The moment of photography of each frame is accompanied with sound in" dication (XT"350 only). to contents M10. ANUAL MODE S11. LAVE MODE 11. SLAVE MODE Slave Mode is a semi"automatic mode. Op" erated in this mode the turntable rotates till the point of making the next frame after pressing the camera shutter release. The mode is more convenient as there is no need to use remote control for the turntable rota" tion, i. e. first the picture is made and then the turntable rotating surface spins automatical" ly till the next frame and so on. The operation order in this mode is as follows: 1. Connect the turntableto the sync termi" nals of the camera (Fig. 11.1) and flash by means of the splitter and cables (Fig. 11.2) as it is pointed out in item 6.2 above via «М» connector. Figure 11.1 Figure 11.2 2.Choose «M» mode by means of the «Mode» button . Figure 11.3 3. Set the quantity of frames points (8 " 16 " 32) by means of «Frame» mode. Figure 11.4 4. Take a picture by pressing the camera re" lease. After that the turntable will automat" ically get to the next frame. Figure 11.5 S11. LAVE MODE 5. Take the next picture when the table has stopped. 6. Take pictures in each point of photography till the turn is completed. The digital display on the control panel shows the frame number. The moment of photogra" phy of each frame is accompanied with sound indication (XT"350 only). In this mode only counter"clockwise rotation is supported. S11. LAVE MODE to contents 12. OPTIONAL AUTO MODE In Auto Mode during the process of photog" raphy the turntable makes one complete turn without any stops. It makes the time of pho" tography shorter and gives the opportunity to improve the 3D series quality when taking pictures of the photo models. The Auto Mode enables a whole series of pic" tures by way of pressing just one button on the remote control. The frames are made au" tomatically as the turntable controller sends the control signal to the camera at each next frame point. This mode is applicable for the digital cameras with the remote control inter" face. The adapter and camera remote control cables are not included in the complete set of equipment. 1. Insert the optional camera remote cable into socket «A» on the control panel by us" ing the remote control cable and adapter connector. Figure 12.1 O12. PTIONAL AUTO MODE 2. Set «A» mode by pressing the «Mode» button. Figure 12.2 3. Set the required quantity of frames (8, 16, 32) by pressing the «Frame» button. Figure 12.3 4. Now, by pressing one of the buttons on the remote control the turntable will be caused to start its rotation in the prescribed direc" tion, and the camera will take pictures at O12. PTIONAL AUTO MODE Figure 12.4 each stop of the turntable in any point of photography. A complete series of pictures will be obtained in this manner. The digital display on the control panel shows the frame number. The moment of photogra" phy of each frame is accompanied with sound indication (XT"350 only). The set parameters will be retained after the turntable is switched off. NOTE: In Auto Mode the turntable synch ca" ble connected to «M» jack may be removed as it is not used. However, the connected synch cable won’t affect the turntable opera" tion in Auto Mode. O12. PTIONAL AUTO MODE to contents F13. REQUENTLY ASKED QUESTIONS 13. FREQUENTLY ASKED QUESTIONS Question 1: What is to be done if the camera does not possess a synch contact for the flash bulb synch cable ? Answer: There is a number of solutions to this p...
Questo manuale è adatto anche per i modelli :Stereo - XT100 (1.24 mb)